background image

 
 

34 

MUSTS5003_05 20211101

 

Transportation 

Users must always dismount the TEK RMD, transfer to the seats installed in the motor vehicle, and tie 
the Tek RMD into the vehicle with a proper tie-down system. Under no circumstances shall the user 
transport the Tek RMD using a motor vehicle while remaining on the device. During transport, the 
device must be turned off via the main switch. The main arms must be folded down when transporting 
the device in a motor vehicle. During transport on lifting platforms or in lifts, ensure that the Tek RMD is 
centered on the lifting platform and take necessary safety precautions.  

 

WARNING:

 

 

Tek RMD is not designed as a car seat and cannot offer the same degree of safety that is offered by a 
standard car seat. 

 

The Tek RMD is not designed for use while in a motor vehicle. Operating the device while riding in a 
motor vehicle may cause instability and tipping, resulting in injury or death, property damage, and 
damage to the device. For transportation in a motor vehicle, always transfer onto a motor vehicle 
seat.  

 

The Tek RMD may only be transported unoccupied by approved transport securement solutions. An 
improper device securement may cause tipping and free movement of the device, resulting in an 
accident, serious injury or death to persons in the vehicle, damage to the device, or damage to the 
vehicle. Also ensure that the wheel locks are not disengaged. 

Spare parts 

Matia Robotics supplies individual parts or modules to Distributors. Your distributor can provide all 
spare parts for your Tek RMD. Matia Robotics does not provide any replacement units. 
 

Storage 

Make sure the device is turned off from the main switch. We recommend charging the batteries at least 
monthly if the Tek RMD is not used. The device shall be stored between -40 F

0

 and 149 F

0

 (-40 C

0

 and 

+65 C

0

). 

 

Disposal 

If the device (all or part of the device) is not being used, it must be disposed of according to national 
environmental regulations. Components of The Tek RMD and the batteries must not be disposed of like 
regular domestic waste. Old and/or defective batteries must be disposed of according to national 
environmental regulations. 
 

Limited Warranty 

This warranty is only for the original buyer of the Tek RMD, who purchases this device new from Matia 
Robotics or its authorized dealer. The warranty becomes void with the resale or the transfer of the 
device. 
Matia Robotics warrants the Tek RMD for a period of one (1) year from the purchase date through Matia 
Robotics or its authorized dealer. The buyer may also have other legal rights based on the country of 
purchase. If the device is proven defective within the warranty period, Matia Robotics will repair or 
replace the device.  
This warranty does not cover devices: 

 

With defective/removed serial numbers 

 

Subject to improper use or maintenance or modifications 

 

Subject to storage or accident or damaged 

due to reasons beyond Matia Robotics’ control

 

 

Used with unauthorized accessories or parts  

Summary of Contents for TEKRMD01











































Reviews: