background image

 
 

31 

MUSTS5003_05 20211101

 

Safety 

This section contains important information for the safe use and operation of this device. 

Always follow the safety instructions provided in this user manual. Failure to do so could cause severe 
injury to you or people around you or damage to your device. Where safety is concerned, only a Tek 
RMD that is in excellent condition is acceptable. 
Safety calls for the constant attention of the user. Matia Robotics strongly recommends that you learn 
and employ safe methods of carrying out basic daily activities. Always consult your physician to 
determine the methods most suitable for your personal abilities. Protect your device and yourself by 
having your Tek RMD serviced on a regular basis. Contact your Matia Robotics Representative 
immediately whenever any part of your Tek RMD fails to function properly as a hazardous situation 
could cause damage to your device and/or personal injury.  
With regular inspection, adjustment, and replacement of worn parts the device will provide many years 
of excellent performance. Safety precautions contained in this manual are general warnings meant to be 
used as safety guidelines. Do not hesitate to contact your personal physician for advice on safety and/or 
assistance. The expected service life of this product is 5 years.  Spare parts and accessories must be 
ordered through Matia Robotics. Only Matia Robotics authorized technical service operators may 
change parts on the device or perform repairs of the device. 

Standards and Directives 

Tek RMD complies with the applicable requirements of ISO 7176 series standards and ANSI RESNA WC-1 
and WC-2 standards. 

General Safety Instructions & Warnings 

 

The Tek RMD is a prescription only (Rx) use device. Any sale of the device apart from a licensed 
healthcare practitioner is forbidden and will result in legal repercussions as well as voiding the 
warranty. In the case of user sale, the user assumes all liability related to the use of the device. Do 
not sell the device to an unauthorized user. 

 

This product is not intended for use by persons under the age of 22 years. Use of the device by any 
person under the age of 22 years will forfeit the warranty and, in the case of children, may lead to 
improper use and could lead to instability or tipping, resulting in injury or death, property damage, 
and damage to the device.  

 

Prior to use of the Tek RMD, the user should be evaluated by a RESNA certified ATP or RET or a 
RESNA certified Seating and Mobility Specialist SMS. Matia Robotics assumes no liability until the 
user is evaluated by the proper RESNA certified representative. Failure to consult the proper RESNA 
certified representative prior to use of the Tek RMD may lead to incorrect use of the device, 
resulting in injury or death, property damage, and damage to the device. 

 

Failure to consult a licensed physician prior to use of the Tek RMD may lead to incorrect use of the 
device, resulting in injury or death, property damage, and damage to the device. Consult a 
physician before operating the Tek RMD. Matia recommends all users to perform the initial 
operation of the Tek RMD in the presence of a personal physician. The physician should establish 
and regularly supervise a user standing program. A caregiver should be present at all times until the 
user is familiar with the operation of the device. 

 

Operating the Tek RMD before initial training by an authorized Matia representative may lead to 
incorrect use of the device, resulting in injury or death, property damage, and damage to the 
device. Do not use the Tek RMD prior to authorized training. All users of the Tek RMD must read 
and understand all instructions in the manual and be trained by an authorized Matia 
representative.  

Summary of Contents for TEKRMD01











































Reviews: