background image

2000

B

D

DIMENSIONS

IMPORTANT

Dimensions are approximate 

Before disposing of carton and/or commencing assembly, please check all the parts to ascertain that none are missing and they are all 
undamaged

.  

No claim for missing/damaged parts will be accepted once the packing carton has been disposed of and/or assembly has 

commenced.
In case of query contact your Stockist with details of model number and details of serial number.

PREPARATION IMPORTANT

1. Please read complete installation instructions before fitting for enclosure and tray (if fitting). 

2. We recommend the use of safety glasses and non slip gloves when handling the glass panels. 

3. Ensure that the product can be

 fixed

 to a 

solid masonry wall 

or suitable 

timber stud work grade C16/C24

 in the area behind the 

wall frames.

4. Shower trays or tiled floors 

must be absolutely level

 where enclosures are fitted

5. If fitting a tray we recommend a 

drainage test 

is carried out before the tray is tiled in position.

6. The assembly should be installed onto a waterproof wall covering and installed after the tray and wall coverings are in place.
Trays with tiling lips should be let into the wall with the tiling lip flush with the wall to allow the tiling to overlap the tiling lip.

7. Seal between tray and tiles.  Remove any excess sealant from the area/joint between the tray and the tiles where the wall mount is 
to be fitted. This will ensure the wall mount fits correctly to the wall and tray/or tiled floor. 

CAUTION:  TEMPERED GLASS CANNOT BE CUT, POLISHED METAL AND CHROME CAN BE SCRATCHED. 

C

AREFULLY 

REMOVE ASSEMBLY FROM CARTON, DO NOT PLACE GLASS ON HARD FLOOR OR EXPOSE EDGES TO IMPACT. DO NOT 
CUT TOP TRACK IN ANY CIRCUMSTANCES.

TOOLS REQUIRED

Masonry Drill bit 6mm, Tape Measure, Screw Drivers, Safety Glasses, Electric Drill, Level, 

Pencil, Adjustable Spanners, Non Slip Gloves, Glass suction lifter, 2mm & 4mm Allen Keys 

MATKI ONE CORNER SLIDER

E - SIDE P

ANEL

C- DOOR 

OPENING 

Side Panel                   E              
MOSCSP760         732-752      
MOSCSP800         772-792     
MOSCSP900         872-892
MOSCSP1000       972-992   
 

Model                      A              B             C           D                          
MOSC1000       978-998     470-490      400        65
MOSC1100     1078-1098    490-510      440        65
MOSC1200     1178-1198    570-590      450        65
MOSC1400     1378-1398   680-700       550        65
MOSC1500     1478-1498   780-800       550        65 
MOSC1600     1578-1598   780-800       650        65 
MOSC1700     1678-1698   880-900       650        65        
  

A - OVERALL

 WIDTH

2020 - 

T

O

P

 OF DOOR

Summary of Contents for One MOSC1000
















Reviews: