background image

9

4.1 CONSOLE DESCRIPTION (OPTION) 

- CONTINUED

CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION

Operating Overview:

1.  From sleep mode press any key to wake up.
2.  Press  

 key to start/pause workout.

3.  During workout you can see Current RPM, Average RPM, Current Heart Rate, Average Heart Rate, Heart Rate Intensity (% Max HR) in the      

 

  top two screen plue user selectable data in the Training screen.

4.  Press 

 key to change data shown in Training screen during exercise(Time, Distance or Scan).

5.  For setting Mode: Long press 

 key. Adjust values using up/down keys 

.

     a.  Heart Rate Pairing: Press 

 key

 for heart rate pairing, you must put on the heart rete chest belt and move to within 12inches (30cm)  

 

      to the console for proximity pairing.

     b.  Press 

 key 

to set Age (or MHR if known).

     c.  Press 

 key 

to end setting Mode.

General: 

 

1.  ZM8-3 uses ANT+ 2.4Ghzwireless radio to transmit data. 
2.  For heart rate an ANT+ heart rate chest belt accessory is available.
3.  A flywheel sensor measures ratation, the gear ratio defaullt setting is 2.9; with wheel size 27inches.
4.  A maintenance mode is available to change default settings.
5.  The ANT+ flywheel sensor (included) needs to be mounted to the bike frame.
6.  The console operates from 3x AAA batteries, the flywheel sensor from a single CR2032 lithium coin cell battery.

Summary of Contents for CXC FC20

































Reviews: