25
Do not use the tool without exhaust pipe and
when the exhaust pipe guard is not properly
installed.
Do not touch the exhaust pipe, there is a risk of
burns.
Only use the fuel recommended in the manual.
Keep gasoline only in containers designed for it,
and store it at a safe location.
While cutting on a slope, always stand below the
cutting tool.
Always make sure no objects or other debris is
collecting in the trimmer head, in the protective
hood, or in the engine.
Always switch o the tool before you put it down.
Do not use any wire, or anything similar in the line
spool.
Only work during daylight, or when the area is
illuminated well using articial lighting.
Subject the tool to a visual inspection before each
use.
Check, if all screws and connecting parts are
tightened.
Always use both hands to hold the tool.
Check the tool, and its components and guards
for damages, or wear and tear before each use,
and have it repaired, if necessary. Never make the
devices for protection and safety inoperable. Do
not use the tool, when damages or signs of wear
become apparent.
Keep the tools clean and fully functional to ensure
better and safer work.
Always maintain a safe distance between the tool
and your body during work.
Always switch o the tool when work will be
interrupted or the location will be changed; wait
until the cutting tools have completely stopped, a
nd turn o the engine.
Never leave the tool without supervision at the
place of work. Store the tool at a safe place when
work will be interrupted.
Persons operating the machine must not be
distracted, or one may lose control over the tool.
Never use the tool during rain, in a humid or wet
environment, and do not store it outdoors.
Should the tool become wet, wait until it is
completely dry before you use it again.
Before starting work, it is recommended to check
the objects to be cut for possible foreign objects
and to remove them. When despite of this you
encounter a foreign object during cutting, switch
o the tool and remove this object.
If the tool is jammed by a foreign object (stones,
piles of grass), switch it o, and remove the object
using a blunt item. Never use your ngers to
remove jammed foreign objects, because this
may cause serious injuries.
Always keep the running tool away from your
body.
Attention: the cutting tool still runs for some
time after the tool is switched off!
Do not overload the engine, and do not use it for
work the tool is not designed for.
Always make sure the ventilation openings are
free of dirt.
Store the tool out of the reach of children.
Store the tool at a safe and dry location.
Check the engine for damages after impact, or
other damages.
Keep body parts and pieces of clothing away from
the trimmer head when you start the engine, or
keep it running.
Summary of Contents for 310.750.230
