26
Always keep in mind that especially during
trimming of lawn edges, gravel enclosures, and
similar locations stone and dirt can be hurled
away from the cutting line.
Never cross roads or paths when the tool is
switched on.
Never cut against hard objects such as stone, etc.
This way you avoid injuries, and damages to the
tool.
Never use the tool without the guards attached.
Never use your hands to stop the cutting device.
Always wait until it stops on its own.
Hold and guide the trimmer head as close to the
ground as possible.
Only cut grass growing on the ground. Do not cut
Dgrass in cracks in walls, growing or on rocks, etc.
Always make sure no objects, or other debris is
collecting in the trimmer head, in the protective
hood, or in the engine.
Only use the tool, when the guard is attached.
Always switch off the tool, before you put it down.
Keep in mind that there is risk of injuries in the
area of the cutting device intended to cut off the
line.
CAUTION: The cutting tool continues rotating for
a few seconds after the engine is turned off.
Put the tool down only after the cutting tool has
completely stopped and the motor is turned off.
When the cutting tool is damaged, it must be
replaced at once.
Always use the original line only. Never use a
metal wire instead of the nylon line.
Tool and cutting tools must be properly inspected
and serviced periodically. Damages must be
repaired by a service center.
Only use accessories recommended by the
manufacturer.
Have your tool serviced only by qualified
personnel and by use of original spare parts only.
This ensures that the tool will work safely in the
future.
Assembly
Check if all parts are included and if they were
damaged during transport before assembly.
1. Place the tool horizontally with the engine
facing towards the ground.
2. Release the clamp screw (19) (A1), and insert
the top and bottom Trimmer tube into the
provided connector (A2).
3. Slightly twist the bottom Trimmer tube to
engage the retention pin (20) in the bore hole of
the connector. Then tighten the clamp screw.
4. To disassemble, loosen the clamp screw, push
the retention pin inwards, and pull the Trimmer
tube apart (A4).
Handlebars
The design of the petrol brush cutter allows for
operation at the right side of the user's body.
- Use the supplied Allen key (14) to loosen the 4
hexagonal socket screws of the handlebar
bracket (l) (B2c).
- Insert the handlebar (2) with the engine
control into the handlebar bracket (1) (B3).
- Slightly tighten the hexagonal socket screws
(B4).
- Tighten the hexagon socket screws.
Summary of Contents for 310.750.230
