background image

CHAPTER 1:  I

mportant

 

S

afety

 

I

nstructions

1

1.1  BEFORE GETTING STARTED

It is the sole responsibility of the purchaser of Matrix Fitness Systems prod-
ucts to instruct all individuals, whether they are the end user or supervising 
personnel, on proper usage of the equipment.

It  is  recommended  that  all  users  of  Matrix  Fitness  Systems  exercise  equip-
ment be informed of the following information prior to its use.

1.2  PROPER USAGE

Do not use the equipment in any way other than designed or intended by 
the manufacturer. It is imperative that all Matrix Fitness Systems equip-
ment is used properly to avoid injury.

Keep hands and feet clear of moving parts at all times to avoid injury.

Unsupervised children must be kept away from this equipment.

Do not wear loose clothing while on equipment.

(T3xi only)

 When it is necessary to immobilize the treadmill, set the display 

to  read  “CHOOSE  PROGRAM  USING  QUICK  KEYS  OR  SPEED  UP  OR 
DOWN KEYS”, then hold down the RESET & ENTER keys. The treadmill 
will  now  display  “IMMOBILIZED.”  In  this  state  the  treadmill  can  not  be 
operated; both the drive motor & elevation motor are disabled. The tread-
mill  will  remain  in  this  state  across  power  cycles,  resets,  etc.  To  return 
to normal operation mode repeat the same key sequence, hold down the 
RESET  &  ENTER  keys.  The  display  will  now  read  “CHOOSE  PROGRAM 
USING QUICK KEYS OR SPEED UP OR DOWN KEYS”

1.3  BEFORE GETTING STARTED

This  Treadmill  is  intended  for  commercial  use.    To  ensure  your  safety  and 
protect  the  equipment,  read  all  instructions  before  operating  the  MATRIX 
treadmill.

When using an electrical product, basic precautions should always be followed 
including the following:

DANGER:  

To reduce the risk of electric shock:  Always unplug this equipment 

from the electrical outlet immediately after using and before cleaning.

WARNING:  

To reduce the risk of burns, fire, electrical shock or injury to persons 

that may be associated with using this product.

An appliance should never be left unattended when plugged in.

  

Unplug from 

outlet when not in use and before putting on or taking off parts.  

This product must be used for its intended purpose described in this lower 
case owner’s manual.

 

 Do not use other attachments that are not recom-

mend by the manufacturer.  Attachments may cause injury.

To prevent electrical shock, never drop or insert any object into any opening

Do not remove the console covers.  Service should only be done by an autho-
rized service technician.

Never operate the treadmill with the air opening blocked.  Keep the air open-
ing clean, free of lint and hair.

Never  operate  product  if  it  has  a  damaged  cord  or  plug,  if  it  is  working 
properly, if it has been damaged, or immersed in water.  Return the unit to a 
service center for examination and repair.

Do not carry this unit by it’s supply cord or use the cord as a handle.

Keep any power cord away from heated surfaces.

Close supervision is necessary when treadmill is used by or near children or 
disable persons.

Do not use outdoors

Do not operate where aerosol (spray) products are being used or when oxygen 
is being administered.

To disconnect, turn all controls to the off position, then remove plug from 
outlet.

Connect this treadmill to a properly grounded outlet only.

CAUTION:   

If  you  experience  chest  pain,  nausea,  dizziness  or  shortness  or 

breath, STOP exercising immediately and consult a physician before continuing.

06'_Treadmills_M.indd   5

7/18/06   4:00:02 PM

Summary of Contents for COMMERCIAL SERIES TREADMILL




























Reviews: