150
Matrix ETERNITY NE System Manual
12.
Select a
Ringer Mode
for the phone from the four options:
•
Ring immediate (it rings immediately as a fresh calls lands on the phone).
•
Ring if idle (rings only if the phone is idle).
•
Ring after a delay (if the call is still not answered).
•
Ring OFF (silent mode).
Default: Ring Immediate’.
13.
If you selected
Ring after a delay
as Ringer Mode, set the
Ring Delay Timer (sec)
, if required, to the
desired value.
The Ring Delay Timer is the time in seconds the system waits on receiving a call before ringing on the IP
phone. The range of this timer is 0 to 99 seconds. Default: 10 seconds.
14.
If you want to enable
Ringer Auto Acknowledge
mode, set the
Acknowledge Timer (sec)
to the desired
value.
The Ringer Auto Acknowledge mode determines when to stop the ring on the IP phone. There are two
options for Ringer Auto Acknowledge:
•
Stop only when the call is answered.
•
Stop after a delay.
To stop the ring on the IP phone after a delay, the Acknowledge Timer must be configured. The range of
this timer is 01 to 99 seconds. Default: 00 seconds.
To stop the ring only when the Call is answered or manually acknowledged, the Acknowledge Timer must
be set to '00'. By default, Ring Auto Acknowledge is turned OFF.
15.
To assign the Ring Destination for the IP phone, select the desired destination for
Play Ring on
. You may
choose
•
Speakerphone:
The ring will be played on the Speakerphone.
•
Headset:
The ring will be played on the Headset.
Default: Speakerphone.
When you select the Headset as the destination, make sure that you set the flag ‘
Headset Connected?’
to
Yes, connect a Headset to the IP Phone.
16.
Select the desired
Ring Tune
according to your/IP phone user’s preference. Default: 1.
17.
Set the
Ringer Volume
to the desired level, from 0 to 7, according to your preference. Default: 5.
18.
To increase/decrease the volume of outgoing speech (Transmit Gain) on the handset of the IP phone, set
the
Handset Transmit Volume
to the desired level, from 0 to 7. Default: 4.
19.
To increase/decrease the volume of incoming speech (Receive Gain) on the handset of the IP phone, set
the
Handset Receive Volume
to the desired level, from 0 to 7. Default: 4.
20.
To increase/decrease the volume of outgoing speech (Transmit Gain) on the headset of the IP phone, set
the
Headset Transmit Volume
to the desired level, from 0 to 7. Default: 4.
21.
To increase/decrease the volume of outgoing speech (Receive Gain) on the headset of the IP phone, set
the
Headset Receive Volume
to the desired level, from 0 to 7. Default: 4.
Summary of Contents for ETERNITY NE
