background image

 

      

               

 

Single Phase EV Charger Protection unit 

 

 

 

                                                                

17 | 

P a g e

 

 

EU Declaration of Conformity (DoC) 

Ref : SP-EVCP-01-2020 

We 

Company name: 

 

matt:e Ltd 

Postal address: 

 

Unit 5  Common Barn Farm  Tamworth Road 

City 

 

Lichfield 

Postcode: 

 

WS14 9PX 

Telephone number: 

 

01543-227290 

E-Mail address: 

 

Info@matt-e.co.uk 

Declare that this DoC is issued under the sole responsibility of the manufacturer. 

 

Apparatus model/Product:   SP-EVCP  

Type: 

 

Single Phase Electric Vehicle Charger Protection 

 

Object of the declaration

 

Electric Vehicle Charger 

Protection units 

SP-EVCP-T(C)   SP-EVCP-M(C)   SP-EVCP-R(C)   SP-EVCP-B(C) 

IP-EVCP-T(C)   IP-EVCP-M(C)   IP-EVCP-R(C) 

The object of the declaration described above is in conformity with the relevant Union 

harmonisation legislation: 

Low Voltage Directive (2014/35/EU) 

The following harmonised standards and technical specifications have been applied: 

 

Signed for and on behalf of:  matt:e Ltd 

Place of issue 

 

Date 

 

 

 

Lichfield, England 

 

 17 June 2020   

J Charlton,   Director 

Emissions 
EN60255-1 2010   Emissions standard for Measuring Relays and Protection Equipment 
EN60255-26 2013   

EN55011 2016 + A1:2017    Emissions Standard for ISM Equipment 
EN55032 2012   Emissions Standard for Multimedia Equipment  

 
Immunity 
EN60255-1 2010   Emissions standard for Measuring Relays and Protection Equipment 
EN60255-26 2013     

EN61000-4-2 2009    ESD Requirements 
EN61000-4-3 2006 + A1 + A2    Radiated Susceptibility 
EN61000-4-4 2012    Electrical Fast Transient Burst Requirement 
EN61000-4-5 2006    Surges Requirements 
EN61000-4-6 2009    Conducted Susceptibility 
EN61000-4-11 2004    Voltage Dips and Interruptions 
Following the provisions of EU EMC Directive 2014/30/EU 

 
EN61439-1 & 2 2011    Low-voltage switchgear and controlgear assemblies. 

 

EN60947-4-1    Low-voltage switchgear and control gear 
EN61009-1   Residual current operated circuit-breakers with integral overcurrent 
EN61008-1   Residual current operated circuit-breakers without integral overcurrent 
EN 60898-1:2019 Electrical accessories - Circuit-breakers for overcurrent protection for household and similar 
installations - Part 1: Circuit-breakers for a.c. operation 
 

Summary of Contents for IP-EVCP-M


















Reviews: