Max 6A-601DA24, Instruction Manual

5

■

If paper is scratched by staples

①

Dispose of staples remaining in the waste box.

●

NOTE: See “Procedure for waste staple disposal”.

②

Visually check for staples remaining in the machine.

③

If there are staples remaining, operate the machine empty a few 

times by pressing the button with no paper inserted.

④

If staples still remain in the machine, insert some paper you do 

not need and perform step 

③

. Then, try step 

⑤

.

⑤

Pull out the waste box and place the machine vertically as 

shown in the diagram. 

⑥

Use tweezers or the like to remove remaining staples. 

●

CAUTION: Do not grip staples with your bare hands. Doing so may 

        lead to injury.

■

If paper jams occur repeatedly

①

Follow the procedure to remove the paper.

●

NOTE: See “Procedure for clearing paper jams”.

②

Check for staples remaining in the machine. Follow the procedure 

to remove staples if they remain. 

●

NOTE: See “If paper is scratched by staples”.

8. Specifications

FCC WARNING

②

⑤

⑥

■

AC ADAPTER INFORMATION

●

Removal capacity noted in the product specifications is when using 80g/

m2

 PPC paper. Depending on the type 

  of paper or staples or the temperature/humidity environment, removal according to specifications may not be 

  possible. In that case, do not attempt to use the   product.

●

If using for a long time continuously, the motor may overheat and staple removal not be possible. In that case, 

  stop using the machine for a while and let the motor cool off before using again.

●

Use for removing 26/6 staples from 30 or fewer sheets of 80g/

m2

 PPC paper. Using in excess of the capacity will 

  cause malfunction.

• Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the 

   equipment.

• AC adaptor with ferrite core must be used for RF interference suppression.

• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause 

   harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Notice (Class B: ERZ-300) 

CAN ICES-3 (B) / NMB-3 (B)

COMMISSION REGULATION (EU) 2019/1782 of 1 October 2019

Electric Staple Remover

24/6, 26/6, 10, copier finisher staples

Model name

Staple types

126 (W) x 273 (D) x 105 (H) mm

External dimensions

2 kg

Weight

Approx. 60W, 2.5A

10°C /50°F -35°C /95°F, Below 80% RH (non-condensation)

Power consumption

DC24V, 2.5A 

Use only specified AC adapter (AC 100-240V, 50-60Hz) 

appended to machine.

Power source

Working Temp. and Humidity ranges

Number of sheets staples can be removed from

Up to 30 sheets (80 gsm, No.35(26/6))

ERZ-300

Product name

MAX CO., LTD.

Manufacturer’s name

0100-01-057739

6-6 Nihonbashi Hakozaki-cho, Chuo-ku, Tokyo, Japan

Address

Commercial registration number and address

Manufacturer’s name or trade mark

Importer Name In Europe
Importer Address In Europe
Importer Name In USA
Importer Address In USA

Model identifier

MAX CO., LTD.

6-6 Nihonbashi Hakozaki-cho, Chuo-ku, Tokyo, Japan

MAX EUROPE B.V.
Antennestraat 45, 1322AH, Almere, The Netherlands
MAX USA CORP.
205 Express Street Plainview, New York 11803, U.S.A.

6A-601DA24
AC100-240V

50-60Hz

DC24.0V
2.7A

64.8W

88.0%

79.0%

0.21W

Input AC frequency

Output voltage
Output current

Output power

Average active efficiency

Efficiency at low load (10 %)

No-load power consumption

Input voltage