background image

2

INDEX  INDEX  ÍNDICE

ENGLISH

Page

3

to 12

FRANÇAIS

Page

13

to 22

ESPAÑOL

Page

23

to 32

DEFINITIONS OF SIGNAL WORDS
WARNING:

Indicates a potentially hazardous situation which, if not avoided, could result in 
death or serious injury.

CAUTION:

Indicates a potentially hazardous situation which, if not avoided, may result in mi-
nor or moderate injury.

NOTE:

Emphasizes essential information.

DÉFINITIONS DES DIFFÉRENTS DEGRÉS D’ AVERTISSEMENTS
AVERTISSEMENT:

Indique une situation éventuellement dangereuse qui, si elle n’est pas 
contournée, pourrait provoquer la mort ou des blessure sérieuses.

ATTENTION:

Indique une situation éventuellement dangereuse qui, si elle n’est pas contournée, 
pourrait provoquer des blessures légères à moyennement sérieuses.

REMARQUE:

Souligne des informations importantes.

DEFINICIÓN DE LAS INDICACIONES DE ADVERTENCIA
ADVERTENCIA:

Indica una situación potencialmente peligrosa que podría causar la muerte o 
graves lesiones si no se evita.

PRECAUCIÓN:

Indica una situación potencialmente peligrosa que podría causar lesiones menos 
graves o leves si no se evita.

NOTA:

Resalta informaciones importantes.

Summary of Contents for NF665/15














Reviews: