background image

3

INDEX

1. GENERAL SAFETY WARNINGS ........................................................3
2. SAFETY WARNING .............................................................................4
3. SPECIFICATIONS AND TECHNICAL DATA ......................................7
4. AIR SUPPLY AND CONNECTIONS....................................................8
5. INSTRUCTIONS FOR OPERATION....................................................8
6. MAINTENANCE .................................................................................12
7. STORAGE ..........................................................................................12
8. TROUBLE SHOOTING/REPAIRS .....................................................12

1. GENERAL SAFETY WARNINGS

1.

WEAR SAFETY GLASSES OR GOGGLES

Danger to the eyes always exists due to the possibility of 
dust being blown up by the exhausted air or of a fastener fly-
ing up due to the improper handling of the tool. For these 
reasons, safety glasses or goggles shall always be worn 
when operating the tool.
The employer and/or user must ensure that proper eye pro-
tection is worn. Eye protection equipment must conform to 
the requirements of the American National Standards Insti-
tute, ANSI Z87.1 (Council Directive 89/686/EEC of 21 DEC. 
1989) and provide both frontal and side protection.
The employer is responsible to enforce the use of eye pro-
tection equipment by the tool operator and all other person-
nel in the work area.

NOTE:

 Non-side shielded spectacles and face shields 

alone do not provide adequate protection.

2.

EAR PROTECTION MAY BE REQUIRED IN SOME ENVI-
RONMENTS

As the working condition may include exposure to high noise 
levels which can lead to hearing damage, the employer and 
user should ensure that any necessary hearing protection is 
provided and used by the operator and others in the work area.

ENGLISH

OPERATING AND MAINTENANCE MANUAL

BEFORE USING THIS COMPRESSOR, STUDY THIS MANUAL TO ENSURE SAFETY WARNING 
AND INSTRUCTIONS.
KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE.

WARNING

READ ALL SAFETY WARNINGS AND ALL 
INSTRUCTIONS.

Failure to follow the warnings and instructions 
may result in death serious injury. 

Save all warn-

ings and instructions for future reference.

WARNING

Summary of Contents for NF665/15














Reviews: