English
- 25 -
Plug in the WLAN USB dongle to Display first, then
press the
Source
button on the remote and switch to
Wireless Display
source.
A screen appears stating that the Display is ready
for connection.
Open the sharing application on your mobile device.
These applications are named differently for each
brand, refer to the instruction manual of your mobile
device for detailed information.
Scan for devices. After you select your Display and
connect, the screen of your device will be displayed
on your Display.
Note:
This feature can be used only if the mobile device
supports this feature. If you experience problems with the
connection check if the operating system version you use
supports this feature. There may be incompatibility problems
with the operating system versions which are released after
the production of this Display. Scanning and connecting
processes differ according to the programme you use. The
maximum supported resolution is 1920x1080. Image quality
may be affected by neighbouring wireless networks and your
internet connection speed.
Connectivity Troubleshooting
Wireless Network Not Available
• Ensure that any firewalls of your network allow the
Display wireless connection.
• Try searching for wireless networks again, using the
Network
menu screen.
If the wireless network does not function properly,
try using the wired network. Refer to the
Wired
Connectivity
section for more information on the
process.
If the Display does not function using the wired
connection, check the modem (router). If the
router does not have a problem, check the internet
connection of your modem.
Connection is Slow
See the instruction book of your wireless modem to
get information on the internal service area, connection
speed, signal quality and other settings. You need to
have a high speed connection for your modem.
Distruption during playback or slow
reactions
You could try the following in such a case:
Keep at least three meters distance from microwave
ovens, mobile telephones, bluetooth devices or any
other WLAN compatible devices. Try changing the active
channel on the WLAN router.
Internet Connection Not Available
If the MAC address (a unique identifier number) of
your PC or modem has been permanently registered,
it is possible that your Display might not connect to
the internet. In such a case, the MAC address is
authenticated each time when you connect to the
internet. This is a precaution against unauthorized
access. Since your Display has its own MAC address,
your internet service provider cannot validate the MAC
address of your Display. For this reason, your Display
cannot connect to the internet. Contact your internet
service provider and request information on how to
connect a different device, such as your Display, to
the internet.
It is also possible that the connection may not be
available due to a firewall problem. If you think
this causes your problem, contact your internet
service provider. A firewall might be the reason of a
connectivity problem.
DisplayPort
DisplayPort version 1.2 is supported via the Display-
Port input and output connectors on your Display.
DP Stream Setting
option in the
System>Set-
tings>More
menu is set as
MST
(Multi-Stream Trans-
port) by default. If a MST compliant source device is
connected to the Display, the streaming data should
be configured on the source device (Daisy-chaining).
If DisplayPort version 1.1 compliant or SST (Single-
Stream Transport) compliant source device with
DisplayPort version 1.2 support is connected to the
Display, DisplayPort output on the Display will work as
a splitter. In this case, same image will be displayed
in all connected Displays.
To be able to stream the same image to all connected
Displays using a MST compliant device,
DP Stream
Setting
option in the
System>Settings>More
menu
should be set as
SST
.
The maximum amount of the Displays that can be
connected by using daisy-chaining function may differ
depending on the source device’s capacity. The image
that will be displayed in all Displays will be defined by
the source device. For example, to be able to stream
4 different FHD images, the source device should be
capable of supporting this operation.
Note:
It is recommended to use a DisplayPort certified cable
for connection. In
SST
operation mode the total amount of
the Displays is limited (a maximum of 7 units) due to HDCP
encryption. If the signal is stable and there is no cable loss,
there will be no limitation in case the source content is not
HDCP-encrypted. For proper operation in
MST
operation
mode make sure your source device is MST compliant. If
your source device is a computer check the specifications of
its graphic card to ensure
MST
compatibility.
HDMI Out
The HDMI port located on the rear left side of the
Display functions as an output port (upper HDMI port,
HDMI Out). This port will not function as an input,
thus no source devices should be connected to this
port. Only the content received from the HDMI input
