background image

Copyright 2013:  Maxford USA

 

Page

 

  

  

 

 

Blériot XI:  S130926

 

product’s original packing materials, complete with all manuals and accessories. Return 

shipping and insurance charges must be prepaid by you, the buyer. 

3.

 

Returned merchandise that is accepted by Maxford USA for credit is subject to a 10% to 20% 

restocking fee (the final amount will be determined by Maxford USA upon receipt and 

examination of the returned merchandise). 

Return address: 

Maxford USA 

15939 Illinois Avenue, #B-C 
Paramount, CA  90723

 

        

                                          IMPORTANT: 

Print the RMA# issued by Maxford USA

 

 

on your package

 

near our address.

 

III.  SPECIFICATIONS: 

 

Wingspan  .....................................................................................................................................................   51 inches 

 

Wing area  ...................................................................................................................................   552 square inches 

 

Length  ............................................................................................................................................................   42 inches 

 

ARF weight   .................................................................................................................................................   3 pounds 

 

Ready-to-fly weight   .............................................................................................................   4 pounds 6 ounces 

 

Power system  ......   Min. of 400W outrunner motor, 60A ESC, and 4 cell 3,000 mAh Lipo battery 

 

Propeller   .......   11-inch diameter x 6- or 7-inch pitch or larger, per your power system’s maker 

 

Radio  .........................................................................   Min. of 3 channels (4 channels if ailerons are used) 

 

Servos  ...........................................................................   2 mini servos (4 mini servos if ailerons are used) 

(Dimensions and weights are approximate.)

 

IV.  PARTS LIST: 

1.

 

Included items 

 

Prebuilt and precovered fuselage, 

horizontal tailplane, elevators, rudder 

and wing. 

 

 

Included aileron option, complete with all 

associated hinges, servo-mounting hatches 

and linkages.

 

 

Top- and bottom-side wing wire supports. 

 

Scale-looking, shock-absorbing  

landing-gear assembly and wheels. 

 

Hardware package, including simulated 

wing wires and fuselage boom wires. 

 

This illustrated Instruction Manual.

 

2.

 

Items you must supply 

 

Epoxy and cyanoacrylate (CA) adhesives, threadlock compound and petroleum jelly. 

 

Common hand tools such as screwdrivers, pliers, etc. 

 

Mininum of three-channel radio system with two mini servos. (Using ailerons requires a four-

or-more channel radio plus two additional mini servos and one 6-inch Y harness.) 

 

Minimum of 400-Watt outer rotor motor with compatible electronic speed control, battery and 
an 11-inch diameter x 6- or 7-inch pitch propeller or as required by your motor. 

3.

 

Optional items you may add 

 

Simulated Anzani 3-cylinder  

fan semiradial engine. 

 

Pilot seat and installation set 
(only), or pilot seat with a 

preglued pilot figure and 
installation kit. 

 

Vintage-style spoked wheels. 

(ARF comes with solid wood wheels.) 
 

Optional seat (only)

 

of 16

 

Summary of Contents for Bleriot XI





















Reviews: