background image

Page 

13

 of 

13

 

 

2.

 

Double-check the control travel directions of the throttle, ailerons, elevator and rudder. 

3.

 

As with all radio-controlled model airplanes, this model must pass the radio range ground check 

recommended by your radio’s manufacturer, or you may not safely fly. 

4.

 

Get into the habit of turning on your transmitter and moving the throttle to minimum before plugging in your 
battery, and operate your electric power system according to the manufacturer’s instructions. 
 

 

REMINDER:

 

An important notice to our customers!

 

T

H I S   P R O D U C T   I S  

N O T

  A   T O Y

.  

The quality and capabilities of your finished model airplane depend on how you build it. 

Your safety depends on how you use and fly it. 

Any testing or flying of this model airplane is done entirely at your own risk. 

 

We thank you for choosing Maxford USA and  

we sincerely wish you many happy landings!

 

 

Manufactured by:

 

Maxford

  

USA

 

RC

 

Model

 

Mfg,

 

Inc.

 

Distributed by: 

Maxford

 

USA

 

RC

 

Distribution

 

Inc.

 

15939

 

Illinois

 

Ave.

 

#C

 

Paramount,

 

CA

 

90723

 

Telephone (voice)  .............................  562-529-3988 
Fax  ....................................................  562-562-6988 
Toll free (orders only) ......................  866-706-8288 

Web site:   www.maxfordusa.com

 

 

Order replacement parts, servos, batteries, gas engines, brushless motors, 

electronic speed controls,  

and a wide variety of other high-quality RC hobby items online at

 

w w w. m a x f o r d u s a . c o m  

Summary of Contents for Hughes H-1 V2














Reviews: