EXIT PWR
ALARM
POWER /
SOLAR IN
BATTERY
INPUT
OPENING
CLOSING
CLOSING
OPENING
ERD
OBD PORT
BLACK BOX
PROGRAMMING
SOLAR MODE
PROGRAM
MOTOR
OVER
LOAD
ERD
MOTOR
OVER
LOAD
MAX
OFF
MAX
SENSE
MAX
SENSE
BATTERY
BACKUP MODE
ERD SENSITIVITY
MOTION CONTROL
OPEN
GATE SPEED
MAG
LOCK
UL
ENTRAP
PRIMARY/
SECONDARY
LINK
STOP
CLOSE
MOTOR
INPUTS
CLOSE
TIMER
MAGLOCK
DELAY
JOG
BATTERY
TEST
INPUT
ERROR
BATTERY
BATTERY
IN USE
REPLACE
BATTERY
LEAVE
CLOSED
LEAVE
OPEN
OPEN
1 TIME
BATTERY VOLTAGE
E
F
1/2
RESET /
MANUAL
RELEASE
ID
PLUG
LINK
OK
MODULE
PORT
MOTOR
POSITION
INPUTS
SLIDER
LIMIT
SWING
LIMIT
GND
OPEN ONLY
NC
OPEN ONLY
10K
PHOTO CLS
NC
OPEN/CLS
NC
GND
12VDC OUT
GND
GND
GND
GND
GND
GND
JOG RIGHT
JOG LEFT
TAMPER IN
TAMPER NO
GATE DISABLE
MANUAL RELEASE
KEYPAD / CARD
GND (-)
(+)
GND
GND
MAX OPEN
FIRE DEPT
RADIO GND
RADIO SIGNAL
STRIKE
CLOSE COM
COM
STOP
OPEN
CLS ONLY
10K
OPEN/CLS
10K
12VDC OUT
NO
COM
NC
ID PLUG
ERROR
24VDC OUTPUT
12VDC OUTPUT
GND
GND
GND
LOOP PWR
OFF
PRIMARY
LEFT
ON/OFF
BATTERY
RIGHT
SECONDARY
ON
QUICK
CLOSE
OPEN
LEFT
OPEN
RIGHT
GATE
OFF
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
MIN
MIN
MAX
MAX
ON
OFF
2.5 sec
1.5 sec
FAULTS
OPERATOR
MATRIX III
OFF
OFF
3
1
14
16
MIN
16
MIN
12
9
7
3
1
14
12
9
7
UL SENSOR N.C.
UL SENSOR 10K
POWER
MODE A
MODE B
EXIT LOOP
LOOP
LOOP
CENTER
SAFETY
GATE OPEN
COM
GATE CLOSED
MIN
MATRIX III
SWING / SLIDE
Gate
Tamper
Relay
The GATE TAMPER is factory set
to OFF (Unarmed). See previous
page for more information about
ARMING GATE TAMPER.
If an existing alarm system
(Building alarm system) is
connected to the GATE TAMPER
relay (see previous page), notify
proper authorities BEFORE
dropping the chain.
IMPROPER Dropping of Chain (Vandalize):
Manual Disconnect switch is
NOT
turned
ON
.
When the chain is improperly dropped (Vandalized), the
OPERATOR ALARM
and
GATE TAMPER
relay will activate. The
operator will shut down all operating functions.
The alarm reset button
MUST
be pressed to turn
OFF
the alarm and reset the operator. If
GATE TAMPER
relay is connected to
an existing building alarm system, then they will get a triggering of their alarm system and should be notified of the situation.
PROPER Dropping of Chain
while GATE TAMPER is ARMED:
1.
Turn Manual Disconnect ON to disable operator alarm.
2.
Drop the Chain.
3.
GATE TAMPER relay WILL be activated.
4.
Service operator.
5.
Reconnect the chain to gate.
6.
Turn Manual Disconnect OFF.
7.
Rearm an alarm system that may be connected to the GATE TAMPER relay.
ON
OFF
Manual
Disconnect
ON
OFF
Manual
Disconnect
Dropping the Chain - GATE TAMPER is ARMED (ON)
Manual Disconnect
Alarm Reset Button
16
UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7
d
Partial open programming
Open and close limits must be learned
(Virtual limits or magnet sensor limits)
1.
Gate must be in closed position.
2.
Press and hold STOP + PROGRAM buttons simultaneously for 5 seconds
until a beep is heard and program LED starts blinking.
3.
Release STOP and PROGRAM buttons
4.
Open gate to desired partial open position.
(For single gate, open gate
minimum 6ft. For dual gate, open gate minimum 4ft.)
5.
Press PROGRAM button
to record partial open position
.
(Program LED
will stay on when partial open position is programmed.
To program partial open position on slider:
To erase partial open: Press STOP + PROGRAM simultaneously
for 5 seconds until the program LED turns off. (Gate must be in closed position.)
