background image

      3

WARRANTY

Every new Crank-Up Satellite System is thoroughly inspected and tested before leaving the factory, 

and is covered by the following two years parts and workmanship warranty from the date of original 

purchase.

Two years parts warranty. The customer is not responsible for the cost of replacement parts if the 

original part is determined to be defective under the terms of warranty. The customer is 

responsible for the cost of replacement parts after two years. This warranty does not cover 

installation or external wiring.

Should any trouble develop during the warranty period please contact SatPlus before the warranty 

period expires. If you do experience a problem with the product contact SatPlus Customer Services 

on 

03 9772 8318

 or 

email info@satplus.com.au.

Please make sure you have the following ready when you call:

• Model Number

• Serial Number

• Date of purchase

• Clear and concise details of the fault

• Details of who installed the product

The warranty does not apply where:

• The product has been abused, misused, improperly installed or improperly maintained

• Repairs have been made or attempted by a third party other than Maxview

• Repairs are required due to normal wear and tear

• Modifications have been made to the product

• The antenna unit has been opened 

• Damaged caused by abrasive cleaning or power washing

• Circumstances beyond the control of Maxview that have caused the product to no longer  

  operate correctly

• Customer is not the original owner or cannot provide proof of purchase

In no event shall SatPlus be liable for any indirect, incidental, or consequential damages from the 

sale or use of the product. This disclaimer applies both during and after the term of the warranty.

This does not affect your statutory rights

CRANK UP NZ INSTRUCTIONS MASTER.indd   3

17/09/2013   13:01

Summary of Contents for Crank-Up B2590/85AU

























Reviews: