background image

      5

SAFETY PRECAUTIONS

Read this manual carefully and become familiar with your satellite antenna. Understand its 

applications, its limitations and any hazards involved. Failure to follow all instructions listed below 

may result in electric shock, fire and/or serious injury. SatPlus declines all responsibility in the event 

of incident or accident if they are due to a non observation of the installation instructions or the way 

the product is used.

No modifications are permissible to the Antenna Unit or Handle Assembly.

Installation

• 

Installation should be carried out by a competent person.

• 

Take care when working at heights keeping work area clean and tidy to avoid trip hazards.

• 

Use creeper boards where necessary to ensure roof construction can support your weight.

• 

Use a recommended adhesive from page 5 to bond the antenna unit to vehicle roof and  

 

follow the manufacturer’s instructions during application. 

• 

Do not travel until adhesive has cured noting that curing times vary with weather  

 

 conditions

• 

Power tools should be used in accordance with manufacturer’s instructions.

• 

All electrical work should be carried out by a competent person. If in doubt seek advice  

 

from a qualified electrician.

Operation

• 

Before starting your journey check that antenna is in the park position.

• 

The maximum speed of vehicle with antenna mounted on roof is 81mph (130km/h).

• 

Never operate the antenna if someone is in close proximity of the antenna.

• 

If high winds or electrical storms are anticipated lower antenna to park position.

• 

Do not allow children to operate the antenna unit.

• 

Do not operate the Crank-Up with snow or ice on the antenna.

Servicing

• 

If in the event that you do experience a problem, or  inspection/ repair is required, contact  

 

SatPlus or your appointed representative/dealer.

• 

No regular maintenance required on the system.

• 

Do not remove cover on Antenna

• 

Do not use solvent or abrasive cleaning agents on the system.

• 

Use a suitable mild detergent to clean the Antenna Unit.

• 

Do not pressure wash the Antenna Unit.

• 

Check the Antenna Unit fixings for mechanical integrity at least once a year.

CRANK UP NZ INSTRUCTIONS MASTER.indd   5

17/09/2013   13:01

Summary of Contents for Crank-Up B2590/85AU

























Reviews: