19
ELECTRONIC CONTROL SETUP INSTRUCTIONS
General User Information
“OUT OF ORDER” SHOWING IN DISPLAY –
This condition
indicates the dryer is inoperative. Diagnostic or failure code
will follow the scrolling message.
“0 MINUTES” SHOWING IN DISPLAY –
This indicates the
cycle is complete and the dryer cannot be operated. Coins
dropped or debit inputs during this condition will be stored in
escrow but cannot be used until normal operation is restored
by opening and closing the door. If a door switch has failed,
it must be replaced before normal operation can be restored.
COLD START (Initial first use) –
Dryer is programmed at the
factory as follows:
45 minutes dry time for PN models; 5 minutes per coin for
PD models.
$1.50 dry price (fixed cycle with top off – PD Models)
$0.00 dry price (fixed cycle – PN Models)
WARM START (after power failure) –
A few seconds after
power is restored, if a cycle was in progress at the time of the
power failure, “RESELECT CYCLE” will flash in the display.
This indicates a fabric setting keypad needs to be pressed
to restart dryer.
PRICING –
After the door is opened and then closed following
the completion of a cycle, the display indicates the cycle price
(unless set for free operation). As coins are dropped or debit
inputs arrive, the display will change to lead the user through
the initiation of a cycle.
There are four (4) types of dryer pricing:
Fixed “Vend” Pricing
A dryer set up for “Fixed Cycle” operation can only accept
additional time accumulated by increments equal to the length
of a complete dry cycle. A maximum of 99 minutes may be
purchased; no additional credit is given with 99 minutes in
the display.
Accumulator Pricing
If the price is set to one coin 1, then accumulator pricing
is in effect. Cycle time can be purchased one coin at a time
(PD models) up to the maximum time of 99 minutes.
IMPORTANT
Electrostatic Discharge (ESD)
Sensitive Electronics
ESD problems are present everywhere. ESD may damage
or weaken the electronic control assembly. The new control
assembly may appear to work well after repair is finished,
but failure may occur at a later date due to ESD stress.
n
Use an anti-static wrist strap. Connect wrist strap to green
earth connection point or unpainted metal in the appliance.
-OR-
Touch your finger repeatedly to a green earth connection
point or unpainted metal in the appliance.
n
Before removing the part from its package, touch the
anti-static bag to a green ground connection point or
unpainted metal in the appliance.
n
Avoid touching electronic parts or terminal contacts;
handle electronic control assembly by edges only.
n
When repackaging failed electronic control assembly
in anti-static bag, observe above instructions.
Fixed Cycle With Top Off Pricing
A dryer set to offer “Top Off” capability will allow time to be
added to an existing dry cycle in increments equal to the
number of minutes of dry time per coin (coin 1), up to 99
minutes, regardless of the cost required to start the dryer. No
credit is given for coins or debit inputs entered when the control
is displaying 99 minutes.
PN Models Set Up as PR:
In Enhanced Debit Mode, the top
off price can be set independently (see VALUE OF COIN 2),
and the top off time is calculated according to the following
equation:
Hundredth increment offset is not applied to top off purchases.
PN Models –
The factory has preset the cycle price to zero.
When this happens, “SELECT CYCLE” will appear rather than
a cycle price. Any cycle started as a free cycle will automatically
terminate when the door is opened.
DEBIT CARD READY –
This dryer has a control that is debit
card ready, but the dryer is not.
Display
After the dryer has been installed and plugged in, the display
will show “0 minutes.”
PD Models
Once the dryer has been plugged in and the dryer door opened
and closed, the display will show the vent price. PN models are
factory preset for free cycles; the display will flash “SELECT
CYCLE.”
PN Models
Control Setup Procedures
I
MPORTANT:
Read all instructions before operating.
The fabric setting keypads along with the digital display
are used to set up the dryer controls. The display can contain
4 numbers and/or letters and a decimal point. These are used
to indicate the setup codes and related code values available
for use in programming the dryer.
How to Use the Keypads to Program the Controls
1.
The WHITES AND COLORS keypad is used to adjust the
values associated with setup codes. Pressing the keypad
will change the value by increments. Rapid adjustment is
possible by holding down the keypad.
2.
The DELICATES keypad will advance the display through
the setup codes. Pressing the keypad will advance the
display to the next available setup code. Holding down
the DELICATES keypad will automatically advance through
the setup codes at a rate faster than 1 per second.
3.
The STOP/PAUSE keypad is used to select or deselect
options.
1.50
PRICE
top off time
full-cycle length
top off price
full-cycle price
=
Summary of Contents for MDE28PD
Page 94: ...94 NOTAS ...
Page 95: ...95 NOTAS ...
