14
OVEN RACKS
Cleaning Method:
■
Steel-wool pad
■
For racks that have discolored and are harder to slide,
a light coating of vegetable oil applied to the rack guides
will help them slide.
STORAGE DRAWER
Check that storage drawer is cool and empty before cleaning.
Cleaning Method:
■
Mild detergent
OVEN CAVITY
Do not use oven cleaners.
Food spills should be cleaned when oven cools. At high
temperatures, foods react with porcelain. Staining, etching,
pitting, or faint white spots can result.
Cleaning Method:
■
Clean cycle:
See the “Self-Cleaning Cycle” section.
Oven Light
The oven light is a standard 40-watt appliance bulb. Before
replacing, make sure the oven and cooktop are cool and the
control knobs are in the Off position.
To Replace:
1.
Unplug range or disconnect power.
2.
Turn the glass bulb cover in the back of the oven
counterclockwise to remove.
3.
Turn bulb counterclockwise to remove from socket.
4.
Replace bulb and then bulb cover by turning clockwise.
5.
Plug in range or reconnect power.
TROUBLESHOOTING
First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call, refer
to the warranty page in this manual and scan the code there with your mobile device, or visit
http://www.maytag.com/product_help
.
In Canada, visit
http://www.maytag.ca
.
Contact us by mail with any questions or concerns at the address below:
In the U.S.A.:
Maytag Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
In Canada:
Maytag Brand Home Appliances
Customer eXperience Centre
200 - 6750 Century Ave.
Mississauga, Ontario L5N 0B7
Please include a daytime phone number in your correspondence.
Problem
Possible Causes and/or Solutions
Nothing will operate
Power supply cord is unplugged:
Plug into a grounded outlet.
Household fuse is blown or a circuit breaker is tripped:
Replace the fuse or reset the circuit breaker. If the
problem continues, call an electrician.
The control displays an F9 or F9 E0 error code:
The electrical outlet in the home may be miswired. Contact
a qualified electrician to verify the electrical supply.
Cooktop will not
operate
The control knob is not set correctly:
Push in knob before turning to a setting.
On ceramic glass models, the oven control lockout is set:
See the “Control Lock” keypad feature in the
“Feature Guide” section.
A Self-Cleaning cycle has been selected:
On some ceramic glass models, the cooktop will not operate
during a Self-Cleaning cycle.
Excessive heat
around cookware
on cooktop
Cookware is not the proper size:
Use cookware about the same size as the surface cooking area, element,
or surface burner. Cookware should not extend more than
1
/
2
" (1.3 cm) outside the cooking area.
Cooktop cooking
results not
what expected
Control knob set to incorrect heat level:
See the “Cooktop Use” section.
Range is not level:
Level the range. See the Installation Instructions.
Cooktop element
cycles on and off
on Hi setting
Element cycling due to a temperature limiter:
This is normal operation. The element may cycle on and off to
keep the cooktop from overheating.
Oven will not operate Delay Start is set:
See the “Cook Time” section.
Control is locked:
Press and hold CONTROL LOCK for 3 seconds to unlock.
Control is in Demo mode:
See the “Electronic Oven Controls” section. Demo mode is used for display
models in a showroom.
Electronic oven control set incorrectly:
See “Electronic Oven Controls” section.
Oven temperature
too high or too low
Oven temperature needs adjustment:
See “Oven Temperature Control” in the “Electronic Oven
Controls” section.
