background image

1

W10562335B

W10562339B-SP

Table of Contents 

DRYER SAFETY ......................................................................... 2
INSTALLATION REQUIREMENTS ............................................. 3

Tools and Parts ...................................................................... 3

LOCATION REQUIREMENTS .................................................... 4 

ELECTRICAL REQUIREMENTS ................................................ 5 

INSTALL LEVELING LEGS ......................................................... 6 

ELECTRICAL CONNECTION .................................................... 7
VENTING ................................................................................... 12

Venting Requirements ......................................................... 12

Plan Vent System ................................................................. 13 

Install Vent System .............................................................. 15

CONNECT INLET HOSES ........................................................ 15
CONNECT VENT ...................................................................... 17
LEVEL DRYER .......................................................................... 17
COMPLETE INSTALLATION CHECKLIST .............................. 18
REVERSE DOOR SWING ......................................................... 18

INSTALLATION NOTES

Date of purchase:

 _________________________________

Date of installation:

 _______________________________

Installer:

 ________________________________________

Model number:

 ___________________________________

Serial number:

 ___________________________________

Electric Dryer Installation Instructions

Para obtener acceso al manual de uso y cuidado en español, o para obtener información  

adicional acerca de su producto, visite: www.whirlpool.com 

Tenga listo su número de modelo completo. Puede encontrar el número de modelo  

y de serie dentro de la cavidad superior de la puerta.

Summary of Contents for WED8000BW





















Reviews: