background image

 
 

GENUINE ACCESSORIES 

INSTALLATION INSTRUCTIONS 

 

 

PART NUMBERS: 

 

 

 

 

 

                              APPLICABLE MODELS: 

0000-8C-Z05  Electrochromic Mirror w/ Compass/Temp/HL                                           2006 >  Mazda5   
0000-8C-L27 Compass/Temp/HomeLink

® 

Installation Kit

 

 

REQUIRED COMPONENTS: 

ITEM  QTY 

DESCRIPTION 

SERVICE PART NUMBER

Mirror Assembly with Compass, Temp and HomeLink

®

 0000-8C-Z05 

 

INSTALLATION KIT COMPONENTS: 

 

Harness Assembly – Power, Battery and Ground 

000-8C-H12 

3 2 

Wire 

Tap 

000-8C-H09 

4 3 

Foam 

Tape 

-- 

5 1 

Temperature 

Sensor 

000-8C-G18 

Harness Assembly – Temperature Sensor 

000-8C-G17 

Tie Wrap (Long) 

-- 

Tie Wrap (Short) 

-- 

9 1 

Wire 

Cover 

000-8C-H11 

10 1 

Protective 

Sleeve 

-- 

11 1 

Installation 

Instructions 

-- 

12 1 

User 

Guide 

-- 

 
 
 
 
 
 
 

 
 

 

 
 

 
 
 
 

 

 

 

 

 

 

HOMELINK

®

 AND THE HOMELINK HOUSE

®

 ARE REGISTERED TRADEMARKS OF JOHNSON CONTROLS, INC. 

 

 

TOOLS REQUIRED: 

Clean Rag 

Fish Wire 

#T20 Torx 

Wire Cutters 

Fiberstick 

Electrical Tape 

 Ratchet 

Phillip's Screwdriver 

Pliers 

4mm Flat Screwdriver 

10mm Socket  

 

Page 1 of 13       

                                    

Revision A

                                                                                   550-0339 

Summary of Contents for 0000-8C-L27














Reviews: