background image

11

1031012 Rev.A 09/05

WIRE HARNESS CONNECTIONS- PASSENGER UNDERDASH, continued

SMALLER BROWN (J-06) CONNECTOR-BOTTOM OF PJB

1. Locate the small brown (J-06) connector on the bottom side of the PJB.

(FIGURE PP)

2. Place (1) IDC wire tap on each of the vehicle wires listed below (using the

side of the IDC wire tap that is open on both ends).

3. Insert the wire from the remote start harness into the other side of the IDC

wire tap and crimp in place with pliers.

11

REMOTE START HARNESS

 VEHICLE WIRE

BLACK/BLUE-DOOR LOCK OUTPUT

  BLACK/BLUE - Pin Y

BLACK/WHITE-DOOR UNLOCK OUTPUT

  BLACK/WHITE - Pin AA

BLACK/RED-TRUNK/HATCH PIN SWITCH

  BLACK/RED - Pin X (5DR) or Pin Z (4DR)

LARGER BROWN (J-05) CONNECTOR-BOTTOM OF PJB

1. Locate the small brown (J-05) connector on the bottom side of the SJB.

(FIGURE QQ)

2. Place (1) IDC wire tap on each of the vehicle wires listed below (using the

side of the IDC wire tap that is open on both ends).

3. Insert the wire from the remote start harness into the other side of the IDC

wire tap and crimp in place with pliers.

REMOTE START HARNESS

  VEHICLE WIRE

BLUE-DOME LIGHT INPUT/OUTPUT

  BLACK/BLUE - Pin U

FIGURE QQ

REMOTE START HARNESS

 VEHICLE WIRE

BLACK- HORN OUTPUT

  BLACK - Pin N

FIGURE OO

RE-MOUNT PJB

1. After all connections have been made, re-mount the PJB and secure with the twist tabs.

2. Re-install the PJB cover.

BLUE (J-04) CONNECTOR-TOP OF PJB

1. Locate the blue (J-04) connector on the top side of the PJB.

(FIGURE OO)

2. Place one (1) IDC wire tap on each of the vehicle wires listed below

(using the side of the IDC wire tap that is open on both ends).

3. Insert the wire from the remote start harness into the other side of

the IDC wire tap and crimp in place with pliers.

FIGURE PP

L/W

GY/V

B/R

W

[W/R]

B/G

B/L

B/Y

B/W

B/L

W/G

{B/P}

@W/G

B/LG

B/O

B/O

AF

W

AE

Y

Z

AB

AA

AC

AD

X

U

V

S

T

Q

R

O

P

M

N

K

L

I

J

G

H

E

F

C

D

A

B

<B>

B

#B/R

PJB J-04 Connector View From Harness Side

B/G

@B/R

B/O

[W/G]

B/Y

B/R

B/L

B/G

B/O

B/G

#

#B/W

AF

W

AE

Y

Z

AB

AA

AC

AD

X

U

V

S

T

Q

R

O

P

M

N

K

L

I

J

G

H

E

F

C

D

A

B

B/L

B/L

B/W

PJB J-06 Connector View From Harness Side

O

[BR/G]

G

P

W/B

Y/B

AK

L/R

AR

@W/R

AT

AG

AC

AA

V

T

R

C

L

O/W

AL

I

O

M

R/Y

Q

S

U

B/L

Z

AB

AF

G/B

A

AM

B

J

@O/L

H

D

K

AS

O/Y

AQ

E

AJ

[B/G]

L

F

#G/O

O/L

<O/B>

G/Y

<P/B>

[G/B]

W

Y

AE

AD

AH

AI

AO

AP

AN

X

N

W/B

G/B

 G/Y

{G/B}

G/L

G/L

PJB J-05 Connector View From Harness Side

Summary of Contents for 0000-8F-L10




















Reviews: