2-Channel Amplifier
ONX2.100
5
LINE OUT
LINE INPUT
L
R
L
R
LEVEL
6V 0.2V
0dB 12dB
FULL LPF HPF
60Hz 13KHz
30Hz 250Hz
BASS EQ
X-OVER
HPF
LPF
POWER
PROTECTION
FEATURES:
- 1
Set of RCA inputs
- LEVEL:
Variable sensitivity from
0.2V to 6V
- BASS EQ:
Adjustable 45Hz bass boost from
0dB to 12dB
- X-OVER:
Selects internal crossover functions
- FULL:
Bypasses all crossovers for full frequency operation
- LPF:
Selects the built in
LOW PASS
filter, variable from
30Hz to 250Hz
- HPF:
Selects the built in
HIGH PASS
filter, variable from
60Hz to 13KHz
- POWER
LED
:
Indicates the powered up and turned on condition
- PROTECTION
LED
:
Indicates a high voltage, low voltage, short circuit,
hard clip, over heating or DC fault condition.
- MODE:
MONO / STEREO.
- LINE OUTPUT:
Full range RCA pass through.
2 Channel Full Range Stereo:
Control checklist:
Interconnect cable checklist:
- Refer to the section “Settings for Best Performance”
- Connect the two inputs of the amplifier to a Radio/CD with quality RCA cables.
Switch setting checklist:
Minimum final loudspeaker impedances:
- 1/2CH X-OVER: FULL
- 2 ohm per channel.
MODE: STEREO
Bridged for Subwoofer Application:
- Connect the mono speaker positive terminal to the LEFT +, and its negative terminal to RIGHT
Here we show how to use the 2 channel amplifiers to power a subwoofer by taking
- as shown.
advantage of the mono bridging capability of all MB Quart amplifiers.
Interconnect cable checklist:
Switch setting checklist:
- A MONO signal source is required to bridge channels 1/2, such as would be available
- X-OVER:
LPF
from the mono sub bass output of an active crossover, whether standalone, or built into
Control checklist:
a head unit or equalizer. If you only have 1 set of RCA outputs from your headunit, you
- Refer to the section
“Settings for Best Performance”
can simply connect those to the inputs for ch 1/2 and switch the
MODE
to MONO. The
Minimum final loudspeaker impedances:
amplifier will auto sum the signal and provide mono output.
- 2 ohm per channel in stereo mode.
Important:
Do not be tempted to connect the hot, or positive outputs, from any source
- 4 ohm mono bridged.
together to obtain a mono signal, as this could very well damage the output stage of
that source.
ONYX
ONYX
POWER INPUT
POWER INPUT
GND REM BA
TT+12V
GND REM BA
TT+12V
SPEAKER OUTPUT
SPEAKER OUTPUT
RIGHT LEFT
RIGHT LEFT
- + - +
- + - +
BRIDGED
BRIDGED
FUSE
FUSE
MONO LINE INPUT
(Unless using procedure
described above)
LINE OUT
LINE OUT
LINE INPUT
LINE INPUT
L
L
R
R
L
R
L
R
LEVEL
6V 0.2V
0dB 12dB
FULL
LPF HPF
60Hz 13KHz
30Hz 250Hz
BASS EQ
X-OVER
HPF
LPF
LEVEL
6V 0.2V
0dB 12dB
FULL
LPF HPF
60Hz 13KHz
30Hz 250Hz
BASS EQ
X-OVER
HPF
LPF
POWER
PROTECTION
POWER
PROTECTION
MODE
MODE
MONO STEREO
MONO STEREO
MODE
MONO STEREO
Summary of Contents for ONYX ONX1.1000D
Page 10: ...9 ...
