MBM FC 10 PLUS Operation Manual Download

Page: 38 / 40

9. PRODUCT SPECIFICATIONS

9.1 Specifications

Stations(bins)

10 stations(bins)

Paper Feed

Roller separator system

Station(bin) Capacity

1.1"[approx.

350sheets of 17-lb bond (64g/

㎡

) paper]

Paper Transport

Belt roller system

Stacking Capacity

2.6"

[

approx. 880 sheets of

17-lb bond (64g/

㎡

) paper]

Paper Stacking System

Right and left index system (20° apart) or straight stacking

Collating Speed

40-70 set/minute (A4 size paper long-edge feeding)

Paper Size

Max.

12.9"

18.5"

(328

469 mm

)

/ Min.

3.8"

5.9"

(95

150mm)

A3SR A3 B4 A4 B5 A5

Paper Weight

52 to 157 g/

㎡

(In case of 157 g/

㎡

, up to A3 size can be used.)

Detection of Station in

use

Stations in use can be checked by trial feed with the CHECK key.

Detection of Paper

Weight

Paper thickness on each station can be checked by trial feed with the CHECK key.

Feed Error Detection

Empty feed, no paper, paper jam, double feed (detection of paper thickness with

photo-electric sensors)

Other Detection

Stacking table full, paper eject jam, back door open/close status, (Staple cartridge empty

and paper jam detection when optional stapler-puncher is mounted).

Four-digit display on the operation panel counter, addition/subtraction (preset)

switch-enabled

Additional Features

- Automatic elevation of paper feed table

- Alternate collation (Neighboring two stations can be used together for the same

sheet/page.

- Insertion of partitioning paper (according to the designated set)

- Programmed insertion of cover paper (loading covers on the top station and back covers

on the bottom: Good for collation for system-notebook, chits, etc.)

- Three levels of paper feed pressure (four levels for Station 1 and 10, and three levels for

Station 2 to 9)

- Three levels of separator pressure (Fourth level built-in while not displayed on the

tablet: Used for special papers)

Power Source

100-240V 50- 60Hz <2.0-1.2A>

Power Consumption

Maximum 120W

Dimensions

W27.2"

D 21.3"

H 41.8" (W690

D540

H1,060 mm)

Dimensions

(with anti-fall plate)

W34.9"

D21.3"

H41.8" (W885

D540

H1,060 mm)

Weight

176.4 lb (79.7 kg)

Specifications are subject to change without prior notice for the sake of improvement.

Summary of Contents for FC 10 PLUS









































Search results

Summary of Contents for FC 10 PLUS

Reviews:

Related manuals for FC 10 PLUS

Brands by name

Popular brands

MBM FC 10 PLUS, Operation Manual

Search results

Summary of Contents for FC 10 PLUS

Reviews:

Related manuals for FC 10 PLUS

Brands by name

Popular brands