Troubleshooting
SYMPTOM
REPAIR
1.
Fuel valve is closed, open valve (gasoline engine).
2.
Engine switch is in “STOP” position, turn switch to “ON” position
(gasoline engine).
3.
Fouled spark plug, clean or replace spark plug (gasoline engine).
Engine does not start or stalls.
4.
Dirty or pugged injection nozzle, clean or replace if damaged.
5.
Electric start; low battery charge, recharge battery.
6.
Starter motor defective or worn, replace starter motor.
7.
Defective or worn ignition switch, replace ignition switch.
1.
Improper or old fuel, remove all fuel from tank & engine and replace
with the proper fresh fuel.
Engine does not accelerate, is hard to
2.
Fouled spark plug, clean or replace spark plug (gasoline engine).
start or runs erratically.
3.
Dirty or pugged fuel filter, replace with new fuel filter.
4.
Dirty or pugged injection nozzle, clean or replace if damaged.
5.
Dirty or clogged air cleaner, clean or replace.
Engine over heats or runs hot.
1. Cooling fins are dirty or plugged, remove debris and clean.
1.
Belt tension too loose, tighten belt per Belt Adjustment section of this
Engine runs at full speed but machine
Manual.
does not move.
2.
Worn belt, replace belt.
3.
Clutch malfunction, replace clutch.
1.
Too much hydraulic fluid in control head, set fluid level per Bleeding and
Adjustment of Hydraulic Controls section of this manual.
2.
Belt is slipping, tighten belt per Belt Adjustment section of this Manual.
3.
Incorrect engine rpm., reset engine rpm per Specifications section of this
Slow or no forward travel speed.
manual.
4.
Material build-up on bottom of plate, remove all debris from bottom of
plate.
5.
Mechanical failure, requires authorized MBW service repair.
1.
Not enough hydraulic fluid in control head, set fluid level per Bleeding and
Adjustment of Hydraulic Controls section of this manual.
2.
Air in the hydraulic system, bleed system per Bleeding and Adjustment of
Hydraulic Controls section of this manual.
3.
Improper adjustment of hydraulic control system, requires authorized
Slow or no reverse travel speed.
MBW service repair.
4.
Incorrect engine rpm., reset engine rpm per Specifications section of
this manual.
5.
Material build-up on bottom of plate, remove all debris from bottom of
plate.
6.
Mechanical failure, requires authorized MBW service repair.
1.
Leaking hydraulic connections, tighten connections.
Loss of hydraulic oil.
2.
Leaking hydraulic line, replace hydraulic hose.
3.
Worn or damaged piston seals, requires authorized MBW service repair.
- 19 -
Summary of Contents for 2900280
