25 of 68
3.1
PACKING AND UNPACKING
The
double
"MK8-
75” trowel remains
substantially
intact
for
packaging
and
transport operations.
The only parts that are removed are
respectively:
●
The seat should be removed from the
rear area by sliding it on the
positioning guides after loosening the
4 fixing bolts;
●
The steering levers that are lowered
(fig 3.1). See the installation section
(PAR. 4.1) for data relating to the
repositioning of these levers;
●
The micro-switch under the seat is
disconnected;
●
The lamps are lowered and turned
inwards by activating the handles (fig
3.1);
●
The battery cable is disconnected;
●
Before starting with packaging it is
recommended to always replace the
feather edge disc to the blades to
protect them from any dents before
insertion into the package following
the procedure given in PAR. 6.2.3;
●
The package, unless otherwise
agreed with the customer, consists of
a
cardboard
case.
Normally
the
machine is directly inserted into the
cardboard case, by moving it from the
top (see PAR. 3.2). The cases are
placed on special wooden pallets heat-
treated for health and hygiene-related
reasons.
The lifting of the case should be
performed from the bottom through a
means of sufficient capacity for the load
to be lifted (approved for a mass greater
than or equal to that to be lifted).
●
The
maximal
weight
of
the
packaged product is 220 kg as
shown in the table of general
specifications on p. 15.
!
CAUTION
Each element of waste must
be collected and relocated
in a special container according
to
the
guidelines
for
the
selective collection of waste; if
released into the environment it
can be a source of pollution and
danger.
3.2
LIFTING AND HANDLING
The total weight of the machine is
190 kg.
The lifting must be performed from the
top.
!
CAUTION
For lifting at more than one
meter
from
the
ground
remember to remove the feather
edge disc before the lifting
operation.
1.
Secure all four straps to the four
hooks on either end: 2 on the right
and 2 on the left of the device at the
top lifting hazard pictograms (fig. 3.3).
Use hooks provided with safety fasteners
which do not allow rope slipping.
!
CAUTION
Slinging /transport gear must
take into account the shape
and volume and the mass
indicated on the label and/or on
the machine specifications
.
Make use of ropes or straps
and lifting gear (crane or forklift
truck) with a capacity greater
than that to be lifted.
Figure 3.2
PACKAGED WEIGHT: MAX 220 KG
Figure 3.1
Summary of Contents for MK8-75
