FleX Controller
– User Manual
19
Version 1.0
McCain Engine flash1 device (McCain Engine FLASH #1 Map Info) initialized
McCain Engine sram device: 200000 at ff000000 Partition number 1
Creating 1 MTD partitions on "McCain Engine SRAM Map Info":
0x000000000000-0x000000200000 : "ram"
McCain Engine sram device (McCain Engine SRAM Map Info) initialized
Generic platform RAM MTD, (c) 2004 Simtec Electronics
ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP)
NAND_ECC_NONE selected by board driver. This is not recommended !!
Scanning device for bad blocks
Creating 1 MTD partitions on "MT29F2G08ABAEAWP":
0x000000000000-0x000010000000 : "atc"
ucc_geth: QE UCC Gigabit Ethernet Controller
ucc_geth: UCC1 at 0xe0102000 (irq = 25)
ucc_geth: UCC2 at 0xe0103000 (irq = 26)
Freescale PowerQUICC MII Bus: probed
fsl,usb-fhci e01006c0.usb: at 0xd18926c0, irq 24
fsl,usb-fhci e01006c0.usb: FHCI HOST Controller
fsl,usb-fhci e01006c0.usb: new USB bus registered, assigned bus number 1
fsl,usb-fhci e01006c0.usb: irq 24, io mem 0x00000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usbcore: registered new interface driver uas
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
NONE Host Was Detected, by default is a 2070_1C Type
hw-rtc hw-rtc.0: rtc core: registered hw-rtc as rtc0
linesync 2070
acfail 2070
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
Registering the dns_resolver key type
hw-rtc hw-rtc.0: setting system clock to 2001-01-17 07:41:28 UTC (979717288)
usb 1-1: new full speed USB device number 2 using fsl,usb-fhci
VFS: Mounted root (jffs2 filesystem) on device 31:4.
Freeing unused kernel memory: 184k init
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
Setting the hostname to McCainEBIII
Mounting filesystems
Running sysctl
Setting up networking on loopback device:
Setting up networking on eth0:
Adding static route for default gateway to 192.168.3.1:
Setting nameserver to 192.168.3.84 in /etc/resolv.conf:
Setting up networking on eth1:
Adding static route for default gateway to 192.168.3.1:
Setting nameserver to 192.168.3.84 in /etc/resolv.conf:
Starting inetd:
Starting the port mapper:
Starting the dropbear ssh server:
EXT3-fs: barriers not enabled
kjournald starting. Commit interval 5 seconds
Summary of Contents for FleX M73101R
