257
Contents Directive 2010/52/EC
9
N°
2010/52/EC
Section
4.1
In particular or in addition to the requirements in standard ISO 3600:1996, the operator’s manual
shall cover the following:
a
adjustment of the seat and suspension related to the ergonomic position of the operator with
respect to the controls and in order to minimise the risks from whole body vibration;
3
b
use and adjustment of the system for heating, ventilation and air-conditioning, when provided;
3
c
starting and stopping of the engine;
2, 5
d
location and method of opening of emergency exits;
3
e
boarding and leaving the tractor;
2, 3
f
the hazard area near to the pivot axis of articulated tractors;
NA
g
use of special tools, if any are provided;
2
h
safe methods used for service and maintenance;
2, 7
i
information about the interval of inspection of hydraulic hoses;
2
j
instructions about how to tow the tractor;
5
k
instructions about the safe use of jacks and recommended jacking points;
2
l
hazards related to batteries and fuel tank;
2, 7
m
prohibited use of the tractor, where overturning hazards exist with mention that the list is not
exhaustive;
2
n
residual risks, related to hot surfaces, such as filling of oil or coolant in hot engines or transmis-
sions;
2, 7
o
the level of protection of the Falling Objects Protective Structure, if applicable;
1, 2
p
the level of protection against hazardous substances, if applicable;
1, 2, 7
q
the level of protection of the Operators Protection Structure, if applicable;
1, 2
4.2
Attaching, detaching and working with mounted machinery, trailers and interchangeable towed
machinery:
a
a warning to strictly follow the instructions outlined in the operator’s manual of the mounted or
trailed machinery or trailer, and not to operate the combination tractor-machine or tractor-trailer
unless all instructions have been followed;
2
b
a warning to stay clear from the area of the three-point linkage when controlling it;
2, 5
c
a warning that mounted machinery must be lowered on the ground before leaving the tractor;
2, 5
d
speed of the power take-off drive shafts in function of the mounted machinery or trailed vehicle;
4, 5, 9
e
a requirement to use only power take-off drive shafts with adequate guards;
2, 5
f
information about hydraulic coupling devices and their function;
5
g
information about the maximum lift capacity of the three-point linkage;
5, 9
h
information about the determination of the total mass, the axle loads, the tyre load carrying capacity
and the necessary minimum ballasting;
6, 9
i
information about the available trailer braking systems and their compatibility with the trailed vehicles; 5
j
the maximum vertical load on the rear hitch, related to the rear tyre size and type of hitch; see
relevant approval documents
5
k
information about using implements with power take-off drive shafts and that the technically pos-
sible inclination of the shafts depend on the shape and size of the master shield and/or clearance
zone, including the specific information required in case of PTO type 3 with reduced dimension;
2, 5
l
a repeat of the data on the statutory plate about maximum allowed trailed masses;
5
m
a warning to stay clear from the area between tractor and trailed vehicle.
2
Operator’s manual Rex Orchard
Summary of Contents for X60 Series
