Care
Point:
The oil level check is completed
with the engine running at
2000rpm for 40 seconds.
1.
The following conditions must be met to allow
an engine oil level check to be carried out:
Care
Point:
•
The vehicle must be stationary
and positioned on a level
surface.
•
Engine running with the throttle
pedal fully released.
•
Neutral gear selected and the
foot brake applied (use left
foot).
If any of these conditions are not
met, a warning message will be
displayed on the instrument
cluster.
Care
Point:
The foot brake must be applied for
the entire duration of the oil level
check.
Care
Point:
The oil level status can be viewed
in the Vehicle information section
in the left hand instrument cluster
display.
2.
Start the engine and navigate to the left hand
cluster display to oil level check.
3.
If all prerequisite conditions have been met
you will be taken to the apply throttle screen.
Care
Point:
Allow the engine oil temperature to
reach a temperature of 70°C
(measured via the oil level
sensor).
Care
Point:
The oil level check will limit the
rpm input to 2000rpm once the
test has begun, but the throttle
must be applied for the duration of
the oil level check. If the throttle
pedal is released and the engine
speed drops below 2000 rpm
during the oil level check, then the
oil level check will abort, and
return you to the apply throttle
screen.
The 40 second countdown timer
will begin when the oil temperature
has exceeded 40°C.
4.
Apply throttle and raise the engine speed to
2000 rpm.
The 40 second countdown timer will begin
when the oil temperature has exceeded 40°C.
Care
Point:
The line on the display indicates
the target oil level.
Care
Point:
Once the oil level check has been
completed and returned a value,
do not continue to test the system.
This may lead to aeration of the oil
and return a false value. To end
the oil level check, release the
throttle and abort back to the
vehicle info menu.
5.
When the timer has reached
'
0
Care
Point:
When the timer has reached
'
0
Care
Point:
The engine must be switched off
and the instrument cluster must be
returned to the vehicle info menu
before carrying out an oil top up
and retest.
6.
If the engine oil is below target level, top up
with the correct quantity of oil, in accordance
to the graphic opposite. Approximately 0.50
litres is required to raise the level from
minimum to target level.
7.
Carry out the oil level check process to ensure
the level is correct.
8.
Top up as required by repeating steps 1-6.
11
Summary of Contents for MP4-12C
