Care
Point:
Renew washer on drain plug.
1
.
!
Install drain plug (2). 50 Nm
Care
Point:
The following process must be followed quickly, so the clutch fluid will not drain back into clutch sump.
Care
Point:
Ensure a
very clean
funnel and pipe are used.
Fill using
new
clutch oil only.
2
.
!
Fill clutch fluid to fill plug (3) level. Pentosin FFL-4
3
.
!
Install drain plug (1), torque to 10 Nm to avoid stress damage on threads.
4
.
!
Install fill plug (3), torque to 10 Nm to avoid stress damage on threads.
Care
Point:
Ensure the clutches are opened, no gears engaged, no torque.
Operate the airbrake a minimum of 2 times.
5
.
!
Run the engine for 2 minute at a fast idle speed of 2000 rpm.
Care
Point:
Ensure the airbrake is retracted.
6
.
!
Stop engine.
7
.
!
Remove fill plug (3).
Care
Point:
Use a suitable container to catch the excess fluid.
8
.
!
Remove drain plug (1).
Care
Point:
Approximately 1.0 litre of clutch fluid will be lost.
Flow of clutch oil will not stop completely.
9
.
!
Allow clutch oil to drain for 60 seconds.
Care
Point:
Drain plug (1) should remain removed.
10
.
Immediately top-up the clutch fluid within one minute until clutch fluid starts to drain out of fill point.
Care
Point:
Renew washer on drain plug.
11
.
Install drain plug (1). 50 Nm
12
.
Install fill plug (3), torque to 10 Nm to avoid stress damage on threads.
Care
Point:
Ensure the clutches are opened, no gears engaged.
Operate the airbrake a minimum of 2 times.
13
.
Run the engine for 2 minutes at fast idle speed of 2000 rpm.
14
.
Stop engine.
15
.
Top-up clutch fluid with 1.0 litres. Pentosin FFL-4
Care
Point:
Renew washer on fill plug (3).
16
.
Install the fill plug (3), torque fully. 50 Nm
17
.
Install components in reverse order.
173
Summary of Contents for MP4-12C
