Care
Point:
The brake bleeding procedure is
carried out using the MDS. The
below steps reference the
procedure stored on the MDS tool.
1
.
!
Connect MDS to vehicle.
2
.
!
Open brake reservoir cap (1).
Care
Point:
Tool must deliver 2.2 bar pressure
(2) and have a minimum of 2 Litres
of brake fluid to carry out
procedure correctly.
3
.
!
Connect pressure bleeding tool.
Care
Point:
Pump the brake pedal during each
phase of the brake bleeding
procedure.
Care
Point:
Pedal pump frequency = 3
seconds applied to 0.5 seconds
released.
4
.
!
Fit bleed bottle to rear left calliper and open
both inner and outer bleed screws (3, 4). M10
17 Nm
5
.
!
Pump pedal until no air is present.
6
.
!
Close bleed screws on rear left calliper (3, 4).
Care
Point:
Pedal pump frequency = 3
seconds applied to 0.5 seconds
released.
7
.
!
Fit bleed bottle to front left calliper and open
both inner and outer bleed screws (5, 6).
8
.
!
Pump pedal until no air is present.
9
.
!
Close bleed screws on front left calliper (5, 6).
Care
Point:
Pedal pump frequency = 3
seconds applied to 0.5 seconds
released.
10
.
Fit bleed bottle to front right calliper and open
both inner and outer bleed screws (7, 8).
11
.
Pump pedal until no air is present.
12
.
Close bleed screws on front right calliper (7,
8).
Care
Point:
Pedal pump frequency = 3
seconds applied to 0.5 seconds
released.
13
.
Fit bleed bottle to rear right calliper and open
both inner and outer bleed screws (9, 10).
14
.
Pump pedal until no air is present.
15
.
Close bleed screws on rear right calliper (9,
10).
Care
Point:
If process needs to be repeated
allow the system to rest for a
minimum of 5 minutes to prevent
damage being caused to the
braking system.
16
.
Disconnect pressure bleeding tool.
17
.
Check brake fluid level and fill to the correct
level. Pentosin 5.1 or Mobil 1.5.1
18
.
Close brake fluid reservoir cap (1).
19
.
Check functionality.
83
Summary of Contents for MP4-12C
