McQuay MicroTech II Operation & Maintenance Manual Download | Manualshive

Page: 18 / 32

background image

Page 18 of 32

OM 750

Priority Result

Application Override Input

햳

Unit Mode Override Input

햳

Unit Mode Output

햳

Heat

Normal (Auto)

햲

Cool

Emergency Heat

Heat

Heat

Normal (Auto)

햲

Cool

Cool

Night Purge

Night Purge

Off

Off

Emergency Heat

Emergency Heat

Fan Only

Fan Only

Heat

Don’t Care

Heat

Cool

Don’t Care

Cool

Night Purge

Don’t Care

Night Purge

Off

Don’t Care

Off

Emergency Heat

Don’t Care

Emergency Heat

Fan Only

Don’t Care

Fan Only

햲

Normal (Auto) is the normal UVC power-up state.

햳

These are network variables.

Table 10. Normal UVC Mode Priority

Occupancy Modes

The UVC is provided with four occupancy modes: Occupied, Standby,
Unoccupied, and Bypass. The occupancy mode effects which heating
and cooling temperature setpoints will be used, effects IAF operation,
and effects OAD operation. The Manual Adjust Occupancy and

Priority Result

Occupancy

Occupancy

Unoccupied

Effective

Override Input

햴

Sensor Input

햴

Input Signal

Occupancy

Output

햴

Occupied

Don’t Care

Don’t Care

Occupied

Unoccupied

Don’t Care

Don’t Care

Unoccupied

Occupied

Don’t Care

Occupied

Unoccupied

Don’t Care

Bypass

Bypass

Contacts Open (Occupied)

Occupied

Null (default)

Contacts Closed (Unoccupied)

Bypass

Standby

Don’t Care

Don’t Care

Standby

Occupied

Don’t Care

Occupied

Unoccupied

Don’t Care

Unoccupied

햲

Null (default)

햳

Contacts Open (Occupied)

Occupied

Null (default)

Contacts Closed (Unoccupied)

Unoccupied

햲

Table 11. Occupancy Mode Priority

Networked Occupancy Sensor network variables, along with the
Unoccupied and Tenant Override binary inputs, are used to determine
the Effective Occupancy.

Priority Result

Emergency Override

Remote Shutdown

Energy Hold

Energy Hold

Unit Mode

Actual UVC

Input

햵

Binary Input

Off Input

햵

Off Output

햵

Output

햵

Action

Normal

Normal

See the Normal

Normal

De-energized

UVC Mode Priority table

Energy Hold Off

Energy Hold Off

Off

Off

Energized

Don’t Care

Energy Hold Off

Off

Off

Pressurize

Don’t Care

Don’t Care

Don’t Care

Off

Pressurize

De-pressurize

Don’t Care

Don’t Care

Don’t Care

Off

De-pressurize

Purge

Don’t Care

Don’t Care

Don’t Care

Off

Purge

Shutdown

Don’t Care

Don’t Care

Don’t Care

Off

Off

햲

Normal here indicated the UVC power-up condition.

햳

De-energized here means that the contacts connected to this binary input are open.

햴

Energized here means that the contacts connected to this binary input are closed.

햵

These are network variables.

Table 9. Special Purpose UVC Unit Mode Priority

햲

The tenant override switch (unit or wall sensor mounted) can be used here to force the UVC into the Bypass Mode.

햳

Typical operation is defined in this row of the table.

햴

These are network variables.

«
...
16
17
18
19
20
...
»

Summary of Contents for MicroTech II

































Reviews:

No comments

Related manuals for MicroTech II

SyncMaster VC240

Brand: Samsung Pages: 39

Brand: Samsung Pages: 91

Brand: Samsung Pages: 80

Brand: Paratec Pages: 8

Brand: J+J Pages: 33

Brand: KAR-TECH Pages: 28

Brand: 2iB Pages: 5

Brand: National Instruments Pages: 7

Brand: National Instruments Pages: 16

Brand: Ultraflex Pages: 7

Brand: Absima Pages: 5

Brand: SOMFY Pages: 112

Brand: Greenheck Pages: 4

Brand: Vector Pages: 8

Brand: Acuity Controls Pages: 5

CompleteStat-Series CS9B-THO

Brand: Bard Pages: 2

Brand: Vent-Axia Pages: 4

Brand: e-survey Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands