background image

Technical Manual 
Blind Push Button Smart 55 

BE-JTA5504.01 

 

 

 

MDT technologies GmbH  •  

51766 Engelskirchen  •  Papiermühle 1

 

 

Phone: +49-2263-

880  •  Fax: +49-2263-4588  •  knx@mdt.de  •  www.mdt.de

 

25

 

 

25

 

4.3.5 Alarms/Lock of Shutter Actuator 

 
In addition, alarms and the lock of the shutter actuator can also be shown in the display. 
The following picture shows the possible settings for this: 

 

Figure 10: Settings – Alarms/Lock of Shutter Actuator 

 
The following table shows the available settings: 
ETS-Text 

Dynamic range 

[Default value] 

Comment 

Alarms/Lock of Shutter 
Actuator 

 

display as text and symbol 

 

display as symbol

 

Setting how alarms and the lock 
are to be shown in the display. 

Parameter for setting: "display as text and symbol". 
Hide text when Alarm/Lock 
active 

 

not active 

 

when button is pressed 

Setting whether text should remain 
active or be deleted when a button 
is pressed. 

Text for Wind alarm 
(highest display priority) 

any text  

(15 bytes allowed) 

[Wind alarm] 

[Frost alarm] 

[Rain alarm] 

[Locked]

 

Texts displayed when the 
respective alarm or lock is 
activated. 

Text for Frost alarm 
Text for Rain alarm 
Text for Lock (lowest 
display priority) 
Displayed symbols 

Symbol for Wind 

 

Symbols are predefined internally 
and appear in the display when the 
respective alarm or lock is 
activated. 

Symbol for Frost 

 

Symbol for Rain 

 

Symbol for Lock 

 

Table 14: Settings – Alarms/Lock of Shutter Actuator 

 

 

Summary of Contents for KNX Smart 55 BE-JTA5504.01































































Reviews: