Mea 7236 Owner'S/Operator'S Manual Download

Page: 22 / 81

Document No

7235-D0001-01

WARRANTY

(continued)

BUYER OBLIGATIONS

5.1

Buyer shall notify MEA of the alleged defect within 10 days of initial discovery and return the allegedly

defective component(s) within 30 days of initial discovery.

5.2

The Buyer must prepay all costs associated with the warranty.

5.3

The Buyer must return components claimed under this warranty to a facility designated by MEA for

evaluation, to establish a claim under this warranty.

5.4

Buyer shall maintain and service MEA Product(s) in accordance with the MEA Product(s) Owner

’

WARRANTY REGISTRATION VALIDATION

6.1

A registration form is provided to the Buyer with the product(s). The form must be fully completed by

the Buyer and returned to MEA upon completion of the installation of the product(s) in order to

validate the warranty. No warranty claims will be processed unless MEA has received a fully

completed warranty registration form.

DISCLAIMER AND WARRANTY SERVICE

7.1

Any labor costs claimed in excess of MEA

’

s set rate and/or times are not provided by this warranty.

If applicable, any labor costs in excess of MEA rate schedules caused by, but not limited to, location

or inaccessibility of the equipment, travel time or labor provided by unauthorized service personnel

are not provided by this warranty.

7.2

This warranty is in lieu of all other warranties or obligations expressed or implied. MEA expressly

disclaims all implied warranties of merchantability or fitness for a particular purpose.

7.3

Warranty claims must be pre-authorized by MEA, and the components returned via prepaid freight

using the designated

“

Returned Merchandise Authorization

”

number and form.

PLEASE NOTE:

Both the MEA Product Registration Form and the Kubota Engine Warranty Registration Form MUST be

returned to MEA in the stamped, self-addressed envelope.

WARNING!!!

Failure to return PRODUCT WARRANTY REGISTRATION

FORMS detailed above may result in the delayed processing of

warranty claims.

Summary of Contents for 7236


















































































Search results

Summary of Contents for 7236

Reviews:

Related manuals for 7236

Brands by name

Popular brands

Mea 7236, Owner'S/Operator'S Manual

Search results

Summary of Contents for 7236

Reviews:

Related manuals for 7236

Brands by name

Popular brands