background image

20

20

APPENDIX B:

Setting Circles

To use the setting circles to locate an object not 
easily found by direct visual observation:
Insert a low-power eyepiece, such as a 26mm, 
into the focuser assembly. Pick out a bright star 
with which you are familiar (or is easily located) 
that is in the area of the sky in which your target 
object is located. Look up the R.A. coordinate of 
the bright star, and also of the object you wish 
to locate, in a star atlas or on the internet. Point 
the telescope at the bright star. Then loosen the 
R.A. setting circle lock knob (see Fig. 42) and 
turn the R.A. setting circle to read the correct 
R.A. coordinate of the bright star; lock the R.A. 
setting circle lock knob to secure the setting 
circle in place (If you are in the northern hemi-
sphere, use the top numbers on the RA setting 
circle. If you are in the southern hemisphere use 
the bottom numbers.). Next, adjust the DEC set-
ting circle by moving the setting circle ring until 

the objects DEC coordinate is aligned with the 0 
registration mark. If the procedure has been fol-
lowed carefully, the bright star should now be in 
the center of the telescope eyepiece and setting 
circles showing the bright star coordinates. 

To locate another object, unlock the RA and 
DEC locks and move the telescope so the RA 
and DEC setting circle coordinates match the 
target object. Then lock each axis and use the 
slow motion controls to track the object.

If when using the setting circles to locate ob-
jects, you do not immediately see the object 
you are seeking, try searching the adjacent sky 
area. Start with the 26mm eyepiece when locat-
ing object since it has a wider field of view than 
the 9mm. Because of its much wider field, the 
viewfinder may be of significant assistance in 
locating and centering objects, after the setting 
circles have been used to locate the approxi-
mate position of the object.

Figure 43:

 DEC setting circle

Figure 42:

 RA setting circle and lock knob

RA Setting Circle 

RA Setting Circle 

Lock Knob

Lock Knob

DEC Setting Circle 

DEC Setting Circle 

RA Setting Circle

RA Setting Circle

Summary of Contents for LX70 Series





























Reviews: