background image

                           

Installation Manual

 

 

3

1

2

4

 

4

Use wire that can withstand temperatures of at least 80°C such as UL1007. 

5

Recommended wire strapping length is 7mm/0.275inch. 

6

Recommended torque setting for terminals is 5 kgf-cm (4.4 Lb-in). 

7

Recommended screwdriver is 3mm, slotted type. 

8

Suggested fuse  and maximum number of the DR class

 PSUs that  can be  connected to a circuit breaker at 

230V are shown as below. 

Model 

Fuse 

Circuit breaker 

C16 

D16 

DR-15 

T2A/L250V 

19 

22 

DR-30 

F2A/L250V 

15 

DR-60

 

F3.15A/L250V 

DR-100

 

F3.15A/L250V 

9

Mounting Instruction

 

Mount as shown in figure only, with input terminals down, or else sufficient cooling will not be possible. 
Admissible DIN rail

TS35/7.5 or TS35/15 

For rail fastening

 

 

a

Tilt the unit slightly rearwards. 

b

Fit the unit over top hat rail. 

c

Slide it downward until it hits the stop. 

d

Press against the bottom for locking. 

e

Shake the unit slightly to check the locking action. 

 
 
 
 
 
 
 
 
 
 

10

For other information about the products, please refer to www.meanwell.com for details. 

 

 

Warning / Caution !! 

1

Risk of electrical shock and energy hazard. All failure should be examined by a qualified technician. Please do 

not remove the case of the power supply by yourself! 

2

Risk of electric arcs and electric shock (danger to life). Connecting both the primary and the secondary sides 

together is not allowed. 

3

Risk of burn hazard. Do not touch the unit in operation and shortly after disconnection! 

4

Risk of fire and short circuit. The openings should be protected from foreign objects or dripping liquids. 

5

Only install the unit in a pollution degree 2 environment (Note.1).

 

6

Please do not install the unit in places with high moisture or near the water. 

7

  The maximum operating temperatures is 50°C for DR-15 and DR-30 series and 40°C for DR-60 and DR-100 series, 

please do not install the unit in places with high ambient temperature or near fire source. 

8

Output current and output wattage must not exceed the rated values on its specification. 

"Click" 

2

DR15-100_1680-21407-0590-E-0418

Summary of Contents for DR-15-12






Reviews: