background image

USB-1808X-OEM User's Guide 

Specifications 

19 

Accuracy 

Analog input DC voltage measurement accuracy 

Table 2. DC accuracy components and specifications. All values are (±) 

Range 

Gain error 

(% of 

reading) 

Offset error 

(mV) 

INL error 

(% of range) 

Absolute 

accuracy at 

Full Scale 

(mV) 

Gain 

temperature 

coefficient 

(% reading/°C) 

Offset 

temperature 

coefficient 

(µV/°C) 

±10 V 

0.020 

1.5 

0.00076 

3.576 

0.00023 

±5 V 

0.020 

1.0 

0.00057 

2.028 

0.00023 

0 V to 10 V  0.020 

1.5 

0.00028 

3.528 

0.00023 

0 V to 5 V 

0.020 

1.0 

0.00014 

2.007 

0.00023 

Dynamic performance 

Table 3. Dynamic performance specifications 

Range 

Condition 

Specification 

±10 V 

Signal-to-noise ratio (SNR)

 

94 dB

 

Signal-to-noise-and-distortion ratio 

(SINAD)

 

94 dB

 

Total harmonic distortion (THD)

 

–108 dB

 

Spurious free dynamic range (SFDR)

 

112 dB

 

Effective number of bits (ENOB)

 

15.3 bits

 

±5 V 

SNR

 

91 dB

 

SINAD

 

91 dB

 

THD

 

–105 dB

 

SFDR

 

107 dB

 

ENOB

 

14.8 bits

 

0 V to 10 V 

SNR

 

87 dB

 

SINAD

 

87 dB

 

THD

 

–104 dB

 

SFDR

 

109 dB

 

ENOB

 

14.5 bits

 

0 V to 5 V 

SNR

 

83 dB

 

SINAD

 

83 dB

 

THD

 

–103 dB

 

SFDR

 

103 dB

 

ENOB

 

13.6 bits

 

Noise performance 

For the peak-to-peak noise distribution test, a differential input channel is connected to AGND at the input 

terminal block, and 32,000 samples are acquired at the maximum rate available at each setting. 

Table 4. Noise performance specifications 

Range 

Counts 

LSBrms 

±10 V 

11.6 

1.77 

±5 V 

18.0 

2.73 

0 V to 10 V 

23.3 

3.54 

0 V to 5 V 

36.1 

5.47 

Summary of Contents for USB-1808X-OEM






























Reviews: