background image

 

1-5. Maintenance, service and faults 

 

The UPS system operates with hazardous voltages. Repairs may be carried out only by 
qualified maintenance personnel.   

 

Caution - 

risk of electric shock. Even after the unit is disconnected from the mains 

(building wiring outlet), components inside the UPS system are still connected to the 
battery and electrically live and dangerous.   

 

Before carrying out any kind of service and/or maintenance, disconnect the batteries 
and verify that no current is present and no hazardous voltage exists in the terminals of 
high capability capacitor such as BUS-capacitors.   

 

Only persons are adequately familiar with batteries and with the required precautionary 
measures may replace batteries and supervise operations. Unauthorized persons must 
be kept well away from the batteries.   

 

Caution -

 risk of electric shock. The battery circuit is not isolated from the input 

voltage. Hazardous voltages may occur between the battery terminals and the ground. 
Before touching, please verify that no voltage is present!   

 

Batteries may cause electric shock and have a high short-circuit current. Please take 
the precautionary measures specified below and any other measures necessary when 
working with batteries:   

remove wristwatches, rings and other metal objects   

use only tools with insulated grips and handles.   

 

When changing batteries, install the same number and same type of batteries.   

 

Do not attempt to dispose of batteries by burning them. This could cause battery 
explosion.   

 

Do not open or destroy batteries. Escaping electrolyte can cause injury to the skin and 
eyes. It may be toxic.   

 

Please replace the fuse only with the same type and amperage in order to avoid fire 
hazards.   

 

Do not dismantle the UPS system. 

 
 
 

 
 
 

 
 
 
 

 
 
 

 
 
 
 

Summary of Contents for ME-1000-WTU


















Reviews: