HUSH endura
™
SPRINTER
4. Adjusting the Hush Optimiser
™
Spray Gun
1. Locate the Solution Flow Screw (#22, page 7) on the Hush Optimiser™ diagram.
2. Face the front of the Hush Optimiser™ gun away from you and turn the Solution Flow Screw clockwise. This reduces
and will eventually stop the flow of solution. DO NOT over-tighten the screw as this will cause damage to the end of
the needle. Once the trigger cannot be pulled back there is no point in tightening the screw down more, this will only
damage the end of the needle.
3. Turning the Solution Flow Screw anti clockwise will increase the flow of solution and turning the solution flow screw
clockwise will decrease the flow of solution.
4. In general, 1 ½ - 2 full turns from the fully closed position will provide a good solution flow. You may find that you want
more or less solution. You can adjust the Solution Flow Screw to your desired setting. NOTE: Opening the Solution
Flow Screw more than 3 turns will not increase the solution flow and will in fact decrease the efficiency of your Hush
Optimiser™ Spray Gun.
5. In general, hold the Hush Optimiser™ Spray Gun 20-30cm from the person being sprayed. Moving the Hush
Optimiser™ Spray Gun back will increase the size of the mist pattern. Moving the Hush Optimiser™ Spray Gun closer
will decrease the size of the mist pattern. The further away you hold the Hush Optimiser™ Spray Gun, the more you will
need to increase the solution flow thus causing abnormal amounts of airborne solution (overspray).
6. Holding the Hush Optimiser™ Spray Gun closer to the person being sprayed along with a minimum flow of solution will
provide the best results, no streaks or running solution and virtually no mist in the spray area.
7. Be sure to move the Hush Optimiser™ Spray Gun at a slow, steady speed keeping the distance of the Spray Gun the
same throughout the application. This will ensure perfect results. It is actually very easy. Practice, Practice, Practice.
8. It is best to hold the Hush Optimiser™ Spray Gun in a vertical position when spraying. If you want to change the
direction of the mist pattern, rotate the position of the air cap rather than turning the Hush Optimiser™ Spray Gun on its
side. Refer to the spray gun pattern diagram on page 7/8.
9. Always hold or store the Hush Optimiser™ Spray Gun in a vertical position. It is a good habit to use, when you are not
spraying.
10. Do not over-tighten the solution flow screw (#22, page 7) as this will damage the end of the needle point. Tighten the
screw until the needle cannot be pulled back. Once this point is reached there is no point in turning the solution slow
screw anymore as this will only cause damage to the needle point.
5
2
Set up and operate your PRINCESS
Tanning System:
1. Plug the PRINCESS
tanning system unit into a proper electrical outlet. Make sure that the electric current
you are connecting to is the same as your unit. (110v or 220v). DO NOT attempt to connect the unit to the wrong
electric current as this will not only damage your unit but also void your warranty.
2. Next, locate the male end of the air hose and connect it to the female quick connect on the PRINCESS
tanning system.
a. To insert the coupler pull back on the ring of the black coupler located on the PRINCESS
tanning
system and connect it to the male connector on the hose. Figure 6.
Fig. 6
b. Release the ring to allow the coupler to snap into place. The hose should now be connected to the
unit Figure 7.
Fig. 7
c. To remove the air hose, pull back on the ring of the black coupler and remove
If you have just finished spraying, the connector may be hot. Allow the PRINCESS unit to cool down
or about 10 minutes before disconnecting the air hose from the turbo unit. Use Caution!
9
