background image

 

 

 

 

 

                     Page 7 of 34      

www.meditouch.co.il 

info@meditouch.co.il 

Tel: (972)-9-8637477 

Fax: (972)-9-8852935 

45 Hamelacha, Poleg industrial zone, Netanya, Israel. 

Zip: 4250574, PO Box: 8306 

DO-15-01-12 

BalanceTutor service manual 211102.doc 

4  Maintenance and safety inspections 

4.1  Preventive maintenance 

The MediTouch authorized service engineers are happy to help you in case problems occur. 

Preventive maintenance can prevent future problems and is indispensable for the safety of technical 

devices. Therefore, ask our service department for an annual preventive maintenance contract, which 

is highly recommended by the manufacturer. Some basic regular maintenance and regular safety 

checks as stipulated in the following chapters are obligatory! 

Before the device switched ON, the user always has to check visually:

 

 

If there are no obstacles prohibiting the proper movement of the perturbation plate 

 

No damage to power supply cable 

 

Power plugs are connected 

 

Accessories such as Harness and Support Lanyard where applicable and available 

4.2  Immediate maintenance 

Immediate maintenance is necessary if: 

!

 

Cable and/or connector plug have been damaged 

!

 

The running belt slides over the running board during walking or running 

!

 

Rubber show cracks (mainly the running belt and the drive belt) 

!

 

Fluid has entered the device 

!

 

A defect or malfunction of the device has been detected or is suspected 

!

 

Coverings have removed off / broken 

Only a properly and regularly serviced device is safe. 

4.3  Annual inspections 

To keep the condition of the device in due order, examinations have to be performed regularly 

according to the local laws and requirements of your country (e.g. in Germany based on BGV 

A3, regulations for prevention of accidents as well as safety requirement inspections in 

accordance with MDD Medical Device Directive, etc.). 

A MediTouch authorized and certified inspection be conducted by MediTouch technical 

personnel or by its worldwide partners only. An annual inspection report (DO-15-01-18) 

delivered to customer at completion. 

Summary of Contents for BalanceTutor



































Reviews: