background image

Page 16 (18)

 

5171

 

31.07.13 TB 
22.10.14 TB

 

LTR-1200

 

User Manual

 

 

 

3.3.3  AC Mains Supply 

The main power connector is a 3-pol Connector for IEC C13 Cables 

Symbol  Parameter 

Comments 

Min 

Typ 

Max  Units 

Electrical Characteristics 
V

ACnom

 

Nominal Input Voltage 

Single Phase 

100 

 

240 

V

AC

 

Input Voltage 

Continuous 

90 

 

264 

V

ACtrans

 

Input Transients 

60ms 

 

 

300 

f

AC

 

Input Frequency 

 

47 

50/60  63 

Hz 

P

IN

 

Input Power* 

1 - 4 Power Supplies 

400 

 

1600*  W 

P

IN110

 

Input Power (110V

AC

1 - 4 Power Supplies 

400 

 

1100  W 

Protection Characteristics  
Fuse 

Slow Fuse 

Integrated into Connector   

10 

 

* When operated on 110V

AC

 mains supply, the max input power is derated to 1100W due to the 10A fuse 

built into the standard IEC C13 housing. Please contact Meerstetter Engineering if you require an 
alternative connector. 

3.4  Error Numbers 

Error Numbers 1 to 99 are universal error numbers, which are identically on each device. For all other 
universal error numbers please refer to the LDD-Family or TEC-Family User Manuals. 
Error Numbers 100 and above are HMI (LTR)-specific. 

3.4.1  RTOS Errors 

Code 

Description 

Error Condition, Remedy 

80 

RTOS_STACKOVERFLOW 

One task has a stack overflow 

Please contact Meerstetter 
Engineering 

81 

RTOS_MALLOCFAIL 

Can not allocate memory 

Please contact Meerstetter 
Engineering 

3.4.2  Routing Errors 

Code 

Description 

Error Condition, Remedy 

100 

ROUTING_LOSTFRAME 

The routing task has lost a 
frame 

Lost frame on internal bus 

101 

COM_TIMEOUT 

Communication timeout to an 
internal device occurred 

No answer for 3x100 ms 

102 

ADDRESS_CONFLICT 

Two internal devices use the 
same address on the bus 

Two identically addresses 
detected 

3.4.3  HMI Errors 

Code 

Description 

Error Condition, Remedy 

110 

DEVICE_VERSION 

HMI and device firmware 
versions not compatible 

Update all device firmware to 
the actual version. 

111 

DEVICE_MISSING 

Unassigned rack output 
terminal detected 

Try to reboot the LTR-1200 

112 

MENU_OWERFLOW 

Menu memory overflow 

Please contact Meerstetter 
Engineering 

113 

UNKNOWN_DEVICE 

Unknown internal device 
recognized 

Please contact Meerstetter 
Engineering 

Summary of Contents for LTR-1200



















Reviews: