background image

 

Installation guide solar modules 

 

 

V1 – April 2015 

13 - 19 

 

4.10

 

Ensure comprehensive fire protection: 

The installation of on-roof systems may influence the fire safety of a building. Improperly installed systems 

can present even more of a danger in the case of fire. Therefore, the modules of an on-roof system must

 

always be installed over a fire-resistant surface. As the module is not regarded as explosion-proof it must 

not  be  installed  near  inflammable  gases  and  vapors  e.g.  close  to  gas  containers,  painting  installations  or 

gasoline  stations.  Furthermore,  the  module  must  not  be  installed  next  to  open  fire  and  flammable 

materials. 

 

5.

 

MECHANICAL INSTALLATION 

Use always structures and materials specifically developed and certified for PV modules installation. 

Avoid shading the back side of the module by the support rack 

 

The  minimum  distance  between  two  fixed  modules  for  linear  thermal  expansion  of  the  module  frames 

should be 5 mm. Nevertheless, the recommended distance between two modules is 20 mm to allow wind 

circulation, in order to reduce pressure loads and improve module ventilation. The PV module should not 

be mounted in such a way that the drain holes of the module can become blocked. 

 

MegaCell PV modules are suitable for mechanical mounting both in portrait and landscape orientation. In 

choosing the orientation, please keep in mind the internal PV module by-pass diode configuration to ensure 

the optimum electrical behavior from any potential shading over the modules. 

 

Galvanic corrosion can occur between the aluminum frame of the PV module and the mounting hardware if 

such hardware is composed of dissimilar metals, especially in harsh environments such as high humidity. In 

these cases, to prevent corrosion, neoprene tape, PVC washers or stainless steel washers should be placed 

between the PV module frame and the support structure. 

 

Additionally,  all  module  support  structures  used  to  support  PV  modules  at  correct  tilt  angles  should  be 

wind and snow load rated by appropriate local and civil Directives prior to installation. 

 

NOTICE: Do not disassemble the PV module and do not remove, drill or modify the frame in any way, as this 

will invalidate the warranty. Please contact the MegaCell Technical Service if module mounting procedure is 

not clear. 

 

5.1

 

Modules with frame 

Installation  using  pressure  clamps  may  be  executed  along  both  sides  of  the  module  frame  according  to 

following instructions . 

Summary of Contents for MBA-GG60 BiSoN Series




















Reviews: