background image

 

Installation guide solar modules 

 

 

V1 – April 2015 

9 - 19 

 

3.3

 

Warning: Danger due to high voltage 

Even  in  disconnected  condition  the  inverter  can  retain  high  voltages,  which  is  a  major  shock  hazard. 

Therefore: 

 

Be very cautious when working with the inverter and wires. 

 

After switching off the inverter as well as before working on the inverter, make sure to regulate the 

time intervals as recommended by the manufacturer so that the high voltage components can be 

discharged 

Make sure to adhere to the assembly regulations of the inverter manufacturer. 

 

3.4

 

Warning: Danger due to electric arc 

The  solar  modules  generate  a  direct  current  when  exposed  to  light.  When  opening  a  closed  circuit,  e.g. 

disconnecting the direct current wire from the loaded inverter, a fatal electric arc may occur. 

 

Never disconnect the solar generator from the inverter while the inverter is connected to the grid 

 

Make  sure  to  use  only  flawless  wire  connections!  Connect  wires  seamlessly  and  keep  them  free 

from dirt 

 

4.

 

PACKAGING, HANDLING AND STORAGE 

4.1

 

Transport, temporary storage and safe unpacking 

 

Please refers to the instructions printed on the cartoon box of each pallet 

 

The modules are sensitive technical components, which must be handled with utmost care. Therefore, be 

particularly careful during transport and temporary storage and leave the modules in the package until they 

are used.  

o

 

Always lift and carry the module with both hands and never carry by means of the junction box.  

o

 

Do  not  drop  the  modules  or  place  them  down  clumsily  on  a  hard  floor  and/or  on  the  module 

corners.  

o

 

Do not place any objects on the modules.  

o

 

Do not stack the modules without protection.  

o

 

Avoid deflection of the modules.  

o

 

Do not walk on the modules. 

o

 

Do not treat with sharp objects and keep all electrical contact areas clean and dry.  

For  documentation  purposes,  the  serial  number  should  be  noted.  If  required,  the  modules  should  be 

temporarily stored in a dry, ventilated room. Clean, non-slip gloves must be worn during all transport and 

installation  work  to  prevent  cut  injuries  from  the  panel  edges.  Contamination  of  the  solar  glass  with 

fingerprints must also be avoided, as this may damage the special coating on the glass. Please pay special 

attention to the warnings on the package as well as on the enclosed unpacking instructions! 

Summary of Contents for MBA-GG60 BiSoN Series




















Reviews: