background image

                                                                             AUGUST/30/2004 

 

2. Press the brake pedal. 

Note: 

If the brake pedal is pressed before the key is in the ON position, the engine will shut down. 

C. TEMPORARY STOP FEATURE: 

This feature allows the vehicle to remain running after the key has been removed from the ignition. This 
feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would 
like to leave the motor running and the climate control on. 
1.Before turning off the engine, press the 

 

button twice on the transmitter and the LED indicator will flash 

3 times to confirm enter. 

2.Turn the ignition key to OFF position. (The engine will stay running.) 
3.The engine will run until the pre-programmed time elapsed or shutdown input is received. 

D. TURBO TIMER MODE:

 (See Start Feature

 12 

Programming) 

Turbo timer mode keeps the engine running after arriving at you destination for a programmable period of 1, 
3 or 5 minutes, This allows the system’s time to conveniently cool down the turbo after you have left the 
vehicle. To activate: 
1. While engine is running, place the transmission gear in the park position and pull up the hand brake. 
2. Before turning off the engine, press and release 

 and 

  buttons at the same time. 

-- The parking light wills turn on to indicate the remote start has entered turbo charge mode. -- 

3. Pull off the “Ignition Key” from the key cylinder.   

-- Engine keeps running. -- 

4. Exit and secure the vehicle.   

--

 Engine continues running until the pre-programmed time elapsed.

 -- 

E. TIMER / TEMPERATURE START:     

This unit can be programmed to start and run the engine every 3 hours or punctually at the same time next 
morning, The engine will run for the programmed running time and then shut down. 

IMPORTANT

: Timer Start should be used only in open areas, Never start and run the vehicle in on enclosed 

space as a garage or carport. 

3 hours timer start with Temperature-control OFF:

 This feature is design for an extreme cold climate 

usage. The system will auto start the vehicle every 3 hours, to prevent engine freezing and hard to start. 
A MAXIMUM OF SIX CYCLES CAN OCCUR.   

3 hours timer start with Temperature-control:

 (See Start Feature

 11 

Programming) 

If you programmed the temperature ON to operate. The system can be programmed to automatically start the 
vehicle engine whenever the temperature inside the vehicle reaches or drops below the preprogrammed 
temperature level. The system will monitor the air temperature every 3 hour and will only start the engine 
during extreme cold temperatures. There are three temperature level to choose form. 

Daily Timer Start:

 The feature is very useful for the driver who wants to run the vehicle punctually at the 

same time next morning. Before set-up of the “Daily Timer Start”, you should set you time for engine 
start.( see Timer Setting /

 

Timer set-up for “Daily Timer Start, page 16) 

ENTER: 

1. Press the 

 

button twice to remote start the vehicle. As soon as the vehicle is running and the parking 

light have turned on or flashing. 

2. Immediately depress the 

  button once, within 2 seconds 

3. Rapidly depresses the 

 

button. The parking light will flash (3) times. The siren or horn chirps (3) times. 

The vehicle is now programmed to start every 3 hours. 

Timer start can be exited manually as follows: 

1. Make sure the remote start system is not operating the engine. 
2. Turn the ignition on. The LED and parking light will flash (4) times. The horn chirps (4) times. 
Or 
1. Press the 

 

button twice to remote start the vehicle. As soon as the vehicle is running and the parking 

light have turned on or flashing. 

2. Immediately depress the 

  button then press and hold the 

 

button for 2 seconds. The parking light 

will flash (4) times. The siren or horn chirps (4) times. The vehicle is no longer programmed to start 
automatically. 

F. TEMPERATURE CHECK

 

You can monitor through the LCD screen, the present indoor temperature of the 
passenger compartment before cooling or heating your vehicle.   
Press the transceiver 

 button first, within 3 seconds press the 

 

button; the 

in-door temperature will be shown on the LCD screen. This reading may be higher than 
actual ambient temperature due to the greenhouse and is relative only the inside vehicle 
temperature.  

 

 

MEGA3700OP 

7

Summary of Contents for MEGA 3700











Reviews: