03282008
Exit
:
Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps to confirm exit.
PASSWORD PIN CODE SETUP:
1. Turn the Ignition switch ‘ON/OFF’ 3 times and stay in the OFF position.
2. Push the Valet switch
8
times and hold it in on the
8
th
push until
four
chirps with a long chirp is heard.
Then release the valet switch.
3. Press and release the transmitter
/ AUX
button once, 2 LED flashes, 2 siren/horn chirps indicate you
are in features “Password Pin Code Programming mode”.
4. Within 15 seconds, begin to enter your chosen 9ths digit by pressing and releasing the valet Switch from
1 – 9 times.
5. Finish by turning the ignition switch to the “On” position.
If the new password code was accepted, the unit would report the newly entered code, by flashing the LED,
The unit will report the new code three times with a one-second pause between each code.
Note: If 15 seconds of inactivity expire, the unit will revert to the last successfully stored code. 3 long chirps
to confirm exit. Will revert to the last successfully stored code
Delete Password Pin Code (Override Without Password Pin Code:
(Factory default setting)
1. Turn the Ignition switch ‘ON/OFF’ 3 times and stay in the OFF position.
2. Push the Valet switch
8
times and hold it in on the
8
th
push until
four
chirps with a long chirp is heard.
Then release the valet switch.
3. Within 15 seconds, press and hold the transmitter
/ AUX
button for 3 seconds. One long chirp to
confirm Deleted the Password Pin Code.
OPERATION MANUAL
A. TRANSMITTER OPERATION:
Transmitter Button
System Function
Remark
Arm & Lock door
-
Arm & Delete The Shock Sensor
Press twice within 3 seconds.
Car Locator
Upon Armed.
(3 seconds)
Panic function
Press and hold for 3 seconds
/ AUX
-
Arm System and Hidden Alarm Function Press within 3 seconds
Disarm & Unlock Door
-
Disarm &Two Step Door Unlock
Press twice within 3 seconds.
/ AUX
(2 sec)
Pop Trunk Release
Press and Hold for 2 seconds
/ AUX
(3 sec)
Panic function
If the H3/6 Gray Wire is not Trunk
release Output (See Alarm Feature
III-2)
¾
or
8
Silent Arm / Disarm
Upon Ignition off
+
(2 seconds) Activate Car-Jacking
Upon Ignition on
Switching code For 2nd
Vehicle
Operation or Garage Door Opener
Press once. LED will illuminate for 3.5
seconds to allow control of 2nd
system.
Second Vehicle Transmitter Programming:
Your 5-button remote transmitter can be utilized to control a 2nd system.
To program to transmitter to the 2nd system, follow instructions for Transmitter programming.
All programming parameters are the same except:
1. Prior to pushing any button on the transmitter, press the side button first.
2. Once this button is pressed, the LED on the transmitter will illuminate for 3.5 seconds.
3. While the LED is illuminated, press any button on the remote control transmitter.
B. LED INDICATORS:
LED Function
LED
Function
Off
Disarmed
2 flashes... pause Trigger on trunk/hood
Slow flash
Armed
3 flashes... pause Trigger on door switch
Fast flash
Passive arming
4 flashes... pause Trigger on Dual Zone Shock Sensor
On (solid)
Valet mode
5 flashes... pause Trigger on Ignition switch
C. CHIRP INDICATORS: D. PARKING LIGHT:
Chirp Function Parking
light
Function
1 chirp
Arm
1 flash
Arm
2 chirps
Disarm
2 flashes
Disarm
3 chirps
Ajar Warning
3 flashes
Disarm / Intrusion
MEGA 470/474; VS 465/474L
8