background image

Wood-pellet burner 

                                         Nani 35

1.

Warnings, Cautions, and Notes

3

Read the safety instructions carefully before
installation. Always follow the safety
instructions during installation and during
maintenance

Installation,   operation,   service,   and   other
work  must   be   carried   out   by   qualified
personnel in accordance with local codes and
regulations.

All   electrical   installation   and   service   work
shall  be   done   by   certified   and   qualified
personnel inaccordance with local codes and
regulations.

Do   not   perform   electrical   work   unless   you
have   the   required   qualifications.   Perform   a
complete   burner   shutdown   and   disconnect
the power supply prior to performing any work
on   the   burner.   Observe   all   guidelines   with
respect to installation, service, or cleaning.

Children and adults should be alerted to the
hazards of high surface temperatures and
should stay away to avoid contact to skinand /
or clothing.

Always follow the instructions for operations

and service.

Only wood pellets are to be
used   with   this   burner.   No
other   fuel   is   to   be   used   in
the burner.

NEVER   BURN   ANY   TYPE

OF   CORN,   CHERRY   PITS,   STICKS   OR
OTHER TYPES OF FUEL IN THE
BURNER.

Burning   wood   pellets   according   to
recommendations   and   the   specifications   set
forth will assure longer burner life and lessen
potential maintenance issues.

There is a risk of burn from touching the
equipment during operation. 
The burner casing, burner body, flange, and
flame trap pipe are hot surfaces during
operation. Keep children away and do not
touch the equipment during operation.

DO   NOT  install   in   a
sleeping room.

DO NOT connect to any air
distribution duct or
system.
DO NOT terminate the vent

in any enclosed or
semi enclosed area, such as; carports, 
garage,
attic, crawl space, under a sun deck or porch,
narrow walkway or closed area, or any 
location
that can build up a concentration of fumes 
such
as a stairwell, covered breezeway etc.

Young children should be carefully supervised
when   they   are   in   the   same   room   with   the
burner.

Electric   switch   must   be
used   to   the   power   supply
cable as an emergency stop

Summary of Contents for NANI
























Reviews: