background image

Megger Limited

Archcliffe Road 
Dover 

T + 44 (0) 1304  502100

Kent,  CT17 9EN

F + 44 (0) 1304 207342

England

E uksales@megger.com 

Megger 

4271 Bronze Way

T +1 (800) 723-2861 (U.S.A. only)

Dallas

T +1 (214) 333-3201 (International)

TX 75237-1019

F +1 (214) 331-7399

U.S.A.

E ussales@megger.com

Megger 

Z.A. Du Buisson de la Couldre 

23 rue Eugène Henaff

T +33 (0) 1 30.16.08.90

78190 TRAPPES  

F +33 (0) 1 34.61.23.77

France 

E infos@megger.com

Megger Pty Limited

Unit 26  9 Hudson Avenue

Castle Hill

T +61 (0)2 9659 2005

Sydney NSW 2125

F +61 (0)2 9659 2201

Australia

E ausales@megger.com

Megger Limited

T +1 416 298 9688 (Canada only)

110 Milner Avenue Unit 1

T +1 416 298 6770

Scarborough Ontario M1S 3R2

F +1 416 298 0848

Canada

E casales@megger.com

This instrument is manufactured in the United Kingdom.
The company reserves the right to change the specification or design without
prior notice.
Megger is a registered trademark.

Part No 6172-913- Edition 2 - Printed in England - 0206
www.megger.com

To replace batteries, 

disconnect test leads

. Remove the battery

cover and carefully remove the battery carrier.

Replace with new batteries. Do not mix old and new batteries

Warning: OBSERVE CORRECT POLARITY

. Incorrect battery

polarity could damage the instrument and invalidate the warranty.

Spare fuse

A blown fuse is indicated by the 

f

symbol. To replace the fuse:

Disconnect test lead and remove the battery cover, replace fuse
with spare provided: type:  500 mA (F) HBC 10 kA 500 V

Summary of Contents for MFT1500/2









Reviews: