Megger TTR20 Instruction Manual Download

Page: 5 / 60

AVTMTTR20 Rev 4 Dec 2015

TABLE OF CONTENTS

NTRODUCTION

......................................................................................................................... 1

About the TTR20 (TTR20-1) ...................................................................................... 1

Electrical Theory and Practice ................................................................................... 2

Applications for the TTR20 ........................................................................................ 4

Upon Receipt of the TTR20 ....................................................................................... 5

Safety First ................................................................................................................. 5

How to Use This Manual ............................................................................................ 5

AFETY

................................................................................................................................... 7

Overview .................................................................................................................... 7

Safety Requirements ................................................................................................. 7

Cautions and Warnings .............................................................................................. 8

CONTROLS

CONNECTORS .............................................................................................. 9

Overview .................................................................................................................... 9

Connectors .............................................................................................................. 10

ETUP

ONNECTIONS

AND

OPERATION

.................................................................................. 11

General Instructions ................................................................................................. 11

Transformers ........................................................................................................... 11

Single-Phase, Two-Winding Transformers .............................................................. 12

Distribution Transformers with Two Secondary Windings ........................................ 12

Three-Phase, Two-Winding Transformers ............................................................... 16

Three-Phase, Three-Winding Transformers ............................................................ 16

Current Transformers (CTs) ..................................................................................... 16

General Operating Procedure .................................................................................. 20

Description of Menus and Test Screens .................................................................. 20

Use with the Optional Printer ................................................................................... 23

HyperTerminal Configuration ................................................................................... 25

AINTENANCE AND TROUBLESHOOTING

.................................................................................... 27

Maintenance ............................................................................................................ 27

Calibration Check ..................................................................................................... 27

Summary of Contents for TTR20





























































Search results

Summary of Contents for TTR20

Reviews:

Related manuals for TTR20

Brands by name

Popular brands

Megger TTR20, Instruction Manual

Search results

Summary of Contents for TTR20

Reviews:

Related manuals for TTR20

Brands by name

Popular brands