PAGE 6
SB-8188 INSTRUCTION & OPERATION MANUAL
Before making any connections to the
. Observe the following:
SB-8188
> Ensure the mains voltage supply matches the label on the supplied plug-
Pack (+/- 10%)
> Ensure that the power switch is OFF
> Ensure that all system grounds (earth) are connected to a common point.
> Avoid powering equipment within a system from multiple power sources
that may be separated by large distance
REMOTE CONTROL
> Connect all audio video sources and destination equipment
> power up all source and destination audio-visual sources
> For each destination output select the appropriate input source by using
> Upon power up the switcher will return to its last used setting before
The front panel input 1~8 select buttons. The supplied IR remote control.
Or through the RS 232 serial communications port.
Powered down.
POWER
1
VGA OUT
8:8 VGA SWITCHER
SW-8188
2
3
4
MONITOR
MONITOR
VGA-1
VGA-2
VGA-3
VGA-4
VGA-5
VGA-6
VGA-7
VGA-8
5
6
7
8
ON
OFF
00/04
00/05
01FE 02FD 03FC 04FB
05FA 06F9 07F8 08F7
31CE 35CA
32CD 36C9
33CC 37C8
34CB 38C7
REMOTE CONTROL
1
2
3
SWITCH POWER ON or OFF
1
Controller with a separate power ON and OFF
INPUT 1~8 MONITOR INPUTS SELECTION
2
3
4
OUTPUT 1~8 VGA SOURCES OUTPUTS SETUP
4
Input - : Switch 8x VGA sources to # 1 Monitor Display
1
CONNECTING THE HARDWARE
Please study the panel drawings below and become familiar with the signal input-output, Power requirements plus any controls
present.
Before using the switcher, please take the time to make certain that the device you wish to connect to its inputs is functioning
properly in all respects. Verify that the video and audio signals are present and are being displayed properly on a suitable device.
If all is well connect the appropriate cables between the output of the device you wish to distribute to output(s) of the switcher to
the carious devices you wish to feed a signal to. Lastly, connect the AC to DC adaptor, connect the DC connector to the switcher
first and then plug the adaptor into a functional AC outlet.
Input -
: Switch 8x VGA sources to # 2 Monitor Display
2
Input -
: Switch 8x VGA sources to # 3 Monitor Display
3
Input - : Switch 8x VGA sources to # 4 Monitor Display
4
Input - : Switch 8x VGA sources to # 5 Monitor Display
5
Input - : Switch 8x VGA sources to # 6 Monitor Display
6
Input - : Switch 8x VGA sources to # 7 Monitor Display
7
Input - : Switch 8x VGA sources to # 8 Monitor Display
8
Output -1 :
VGA Signal source device # 1
VGA-1
Output -2 :
VGA Signal source device # 2
VGA-2
Output -3 :
VGA Signal source device # 3
VGA-3
Output -4 :
VGA Signal source device # 4
VGA-4
Output -5 :
VGA Signal source device # 5
VGA-5
Output -6 :
VGA Signal source device # 6
VGA-6
Output -7 :
VGA Signal source device # 7
VGA-7
Output -8 :
VGA Signal source device # 8
VGA-8
HOW TO SETUP IR CODES :
POWER ON : 00FF 04FB
POWER OFF : 00FF 05FA
INPUT#1 / OUTPUT#1 : 01FE 31CE
INPUT#1 / OUTPUT#2 : 01FE 32CD
INPUT#1 / OUTPUT#3 : 01FE 33CC
INPUT#1 / OUTPUT#4 : 01FE 34CB
INPUT#1 / OUTPUT#5 : 01FE 35CA
INPUT#1 / OUTPUT#6 : 01FE 36C9
INPUT#1 / OUTPUT#7 : 01FE 37C8
INPUT#1 / OUTPUT#8 : 01FE 38C7
INPUT#2 / OUTPUT#1 : 02FD 31CE
INPUT#2 / OUTPUT#2 : 02FD 32CD
INPUT#2 / OUTPUT#3 : 02FD 33CC
INPUT#2 / OUTPUT#4 : 02FD 34CB
INPUT#2 / OUTPUT#5 : 02FD 35CA
INPUT#2 / OUTPUT#6 : 02FD 36C9
INPUT#2 / OUTPUT#7 : 02FD 37C8
INPUT#2 / OUTPUT#8 : 02FD 38C7
INPUT#4 / OUTPUT#1 : 04FB 31CE
INPUT#4 / OUTPUT#2 : 04FB 32CD
INPUT#4 / OUTPUT#3 : 04FB 33CC
INPUT#4 / OUTPUT#4 : 04FB 34CB
INPUT#4 / OUTPUT#5 : 04FB 35CA
INPUT#4 / OUTPUT#6 : 04FB 36C9
INPUT#4 / OUTPUT#7 : 04FB 37C8
INPUT#4 / OUTPUT#8 : 04FB 38C7
INPUT#3 / OUTPUT#1 : 03FC 31CE
INPUT#3 / OUTPUT#2 : 03FC 32CD
INPUT#3 / OUTPUT#3 : 03FC 33CC
INPUT#3 / OUTPUT#4 : 03FC 34CB
INPUT#3 / OUTPUT#5 : 03FC 35CA
INPUT#3 / OUTPUT#6 : 03FC 36C9
INPUT#3 / OUTPUT#7 : 03FC 37C8
INPUT#3 / OUTPUT#8 : 03FC 38C7
Monitor IN / VGA OUT
Meicheng
